![]() |
DBW Gas Pedal Adpater bracket for truck/suv pedal
4 Attachment(s)
DBW mounting bracket for 03-07 Truck/SUV Pedal $120 Shipped via USPS (**adjusted 10/4/2022) Paypal: robhartley@aol.com, enter "TPB" in message block. *** All purchases now include: USPS shipping in CONUS, paypal fees and all the necessary hardware to install the pedal bracket. *** After receiving many of requests for pedal bracket that will work with the 03-07 truck pedal, I fabricated this pedal bracket. This is a bolt in bracket that uses the 03-07 truck/SUV DBW pedal (may fit others) for the 67-72 LS conversions. Let me know if you have any questions or suggestions. ***** GEN IV flat brackets for the 05+ Corvette Pedal can be found here: http://67-72chevytrucks.com/vboard/s...d.php?t=631165 ***** **** PEDAL MOUNT INSTALL INSTRUCTIONS **** 1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten. 2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit. 3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts. 4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket. 5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly. 6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly. 7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary. 8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly. 9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket. NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly. If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase! |
Re: Gas Pedal Adpater bracket for truck/suv pedal
bump
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
3 brackets sold. 9 left.
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
5 brackets sold. 7 left.
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
6 brackets sold, 6 left.
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
1 Attachment(s)
**** INSTALL INSTRUCTIONS ****
Pedal mount instructions: 1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten. 2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit. 3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts. 4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket. 5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly. 6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly. 7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary. 8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly. 9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket. NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly. If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase! |
Re: Gas Pedal Adpater bracket for truck/suv pedal
I want one
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
I want one Rob!
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
Quote:
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Sorry, I forgot about it, but just sent paypal
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
R |
Re: Gas Pedal Adpater bracket for truck/suv pedal
Bump for a great seller. The bracket installed easily and is a great time saver.
http://i96.photobucket.com/albums/l1...1/IMG_0025.jpg |
Re: Gas Pedal Adpater bracket for truck/suv pedal
hi I was wondering if you have any brackets left?
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
Quote:
Thanks Jonathan! |
Re: Gas Pedal Adpater bracket for truck/suv pedal
Just got your PM, I'll take one well!
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Hey man will this work on a 2009 pedal?
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
Quote:
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
I want one too.
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Payment sent. Thanks
|
Re: Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Payment sent, Thanks
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Any plans for making these for a 60-66?
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
ok thanks
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Got a new batch of the pedal brackets!!!
***10 Jan 2015 UPDATE: All new purchases will now include: USPS shipping in CONUS, paypal fees and all the necessary hardware to install the pedal bracket for only $100. Hopefully this will make payment and installation a little easier. Paypal is robhartley@aol.com. *** |
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Got mine the other day! Super fast shipping and a top notch piece too! Thanks!
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
1 Attachment(s)
Thanks Rob quality product.
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
very nice. i'll see if you still have any within a month or 2...got other things to spend money on to get the swap done still :) looks good tho sir!
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Hey rob I'm going to need one of these brackets after my recent purchase. I have a 2005 Escalade pedal, this bracket will work right?
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
I got the pedal bracket in Friday Rob, nice piece and fast shipping, thanks.
|
Re: DBW Gas Pedal Adpater bracket for truck/suv pedal
Quote:
|
All times are GMT -4. The time now is 03:30 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com