No Limit Spy Photos
2 Attachment(s)
Spy Photos
|
Re: No Limit Spy Photos
New "NoLimit Member" jig?
|
Re: No Limit Spy Photos
Very interesting.....
|
Re: No Limit Spy Photos
Kinda Chris Alston looking,... isn't it.
|
Re: No Limit Spy Photos
1 Attachment(s)
New Parts
|
Re: No Limit Spy Photos
You going to offer it coilover or air bags?
|
Re: No Limit Spy Photos
Quote:
|
Re: No Limit Spy Photos
Quote:
|
Re: No Limit Spy Photos
Hopefully in two weeks. - need to make sure there ready to go. Plus, No Limit dealers get first crack at a pre-release.
|
Re: No Limit Spy Photos
Any spy photos for the rear ?
|
Re: No Limit Spy Photos
What gen is this for? 73-87?
|
Re: No Limit Spy Photos
We are working on an updated version of our Wide-Ride 3 to fit as a bolt-in for 63-72, and 73-87
|
Re: No Limit Spy Photos
probably a stupid question, but would this work on the old square body 1 tons? or is the frame a different setup on them compared to the 1/2's?
|
Re: No Limit Spy Photos
Quote:
|
Re: No Limit Spy Photos
Is the spy still on special assignment ?
|
Re: No Limit Spy Photos
any updates?
|
Re: No Limit Spy Photos
The spy is wet sanding today. We are finalizing motor mount towers at this point. Complex forming is holding us up, have to make new forming dies.
|
Re: No Limit Spy Photos
update ?
|
Re: No Limit Spy Photos
Motor mount towers are done, and after a week, we're finally rested up from the Del Mar thrash. We are shooting an install this weekend, well saturday, I'll post up some on monday. Happy Easter.
|
Re: No Limit Spy Photos
tomorrow is Monday.
|
Re: No Limit Spy Photos
Will this work with the current rack & pinion set up you offer? Is there going to be control arms offered also?
|
Re: No Limit Spy Photos
This crossmember is on a bit of a different track than most. We are moving away from the C-10 components. This will be a new version of our Wide-Ride IFS, a complete IFS package including the crosmember, A-arms, coil-overs, shockwaves, or bags/shocks, spindles, brakes, power rack, and sway bar. The spindle is based on a late model Impala, with 12" drilled/slotted rotors, your choice of any 5 lug pattern, sorry, no 5 lugs yet. The track width is 63" hub to hub. Groung clearance on the crossmember is raised 2" over stock, and ride hieght, without a dropped spindle is a 4" to 5" drop from stock, and 2" drop spindles are avail. Motor mounts are included, and will fit SBC, BBC, and LS.
|
Re: No Limit Spy Photos
Looks good Rob!
|
Re: No Limit Spy Photos
2 Attachment(s)
Update
|
Re: No Limit Spy Photos
Is the Impala spindle taller them the c10 spindle ?
|
Re: No Limit Spy Photos
Quote:
|
Re: No Limit Spy Photos
10lbs on the spindle a lone is a pretty good saving so to reduce more weight are you going to offer chrome molly control arms or does that fall into cost does not warrant the weight saving.
|
Re: No Limit Spy Photos
probably not. Cost-vs-gains may not be worth it for the marketplace. For the street, I doubt there would be any noticable improvements, remember, only 1/2 of the arm is unsprung weight, 1/2 must be counted as sprung weight, as it is mounted to the frame. The same is true with the shock and spring, the weight is split 1/2 and 1/2. It's out on the end, the spindle, rotor, caliper, and wheel and tire, thats where the gains can be noticed.
|
Re: No Limit Spy Photos
Are you going to run one of these on JT?
|
Re: No Limit Spy Photos
Quote:
|
Re: No Limit Spy Photos
Are you looking to have a complete front and rear system. I would like to buy a complete kit, that way I do not have to peice one together. Because I am sure I would jack something up....ha ha.
|
Re: No Limit Spy Photos
Yes tony, our goal is to offer choices for both front and rear suspensions, with a goal of fixing or improving handling and steering woes. Kits will breakdown as follows:
Stock style front. Rack and Pinion steering system - no bump steer, quick ratio Upper and Lower A-Arm set - Reposition wheel, improve caster/camber New variable rate springs, 2" drop Front sway bar kit Raised upper shock mount kit These parts can be used a-la-cart to upgrade any truck, and will work with any spindle/brake Wide-Ride IFS A complete bolt in IFS system, Coil-over, Shockwave, or bag&shock. Uses No Limit Impala clone spindles & brakes, 12", easily upgraded to Wilwood or Bear. P/S rack and swaybar included. 5" drop at ride hieght. Trailing arm parts 2" block kits Pro Panhard rod system Re-located shock mount kit High mount rear sway bar 3" drop variable rate springs These parts can be used to upgrade any OE trailing arm rear suspension C-10 FatBar Curently a weld-on, but soon to be a bolt-on with OE hole locations. Available with coil-over, Shockwave, or bag & shock. Should be used with a bolt in C notch. Adjustable for 4" to 6" drop. Long-to-Short rail kit. Been on this for a while, about to go to production. This is a complete rear rail and crossmember kit. The rail is kicked up 4" above stock. Raising the bed floor is required. Can be used to shorten a longbed, or raise the rails on a shortbed. Complete bolt together install. This rear rail assembly will work with factory type trailing arms, or No Limit FatBar suspension. More on this in an upcoming StreetTrucks issue. |
Re: No Limit Spy Photos
Mr. Rob
Thank you for the reply, I am still a few months out from buying a kit. I am just doing some home work early. I can wait to see what you and the guys at the shop come up with. |
Re: No Limit Spy Photos
wide ride and fat bar for me.
|
Re: No Limit Spy Photos
1 Attachment(s)
i´m a little confused!
I tried to find a bolt in IFS for my 81 Chevy longbed that gives more ground clearance and corrects the geometry and improves the handling and steering and moves the front wheels a bit forward for the looks! Currently i drive a set off 2.5" Spindles with 2" lowered coilsprings and a 6" flipkit without a c notch All from Bell Tech with their nitro drop shocks! The problem is that the LCA´s hit speedbumps very often and it hurts ears and soul and the suspension suffers bad from that! Does the no limit Kit raise the crossmember only or are the mountingpoints for the lca´s higher too? Would the brakes fit with my 15" Wheels? What would a kit cost and the shipping to Germany and what parts do i need additionally? Any info would be greatly apreciated! Volker Attachment 919842 |
Re: No Limit Spy Photos
The bolt in Wide-Ride is a whole new suspension system. Yes, the crossmember and A-arms are raised for clearance as well as a lowered stance. If you have 15" wheels that fit with the OE truck 12" brakes, then they will fit with the No Limit/Impalla 12" brakes. As long as they are 5 lug (we do not currently have a 6 lug rotor for these IFS systems). Wide rides are complete from hub to hub. To complete the instalation you will need * Power steering hoses (we have a kit for $145) * Lower steering U-Joint ( 3/4-36 spline $82) * We recomend a new upper steering U-joint and new shaft (appx $100) * Paint, brake fluid and grease * You may need to re-plumb the front brake lines, new flex lines to the calipers are included. Motor mounts are included. The complete IFS list $ 2950, I would need a delivery address and I can get a shipping quote.
|
Re: No Limit Spy Photos
Thanks for the fast answer!
I read the "make it handle" thread and many of the terms are difficult to understand for a none pro like me! My truck doesn´t ride to bad but the outside of the fronttires are bald after 9500 miles and the steering is very sloppy! So your complete setup is the best thing to get in the truck for driving pleasure, right? That sounds great and seems to be everything i need to get my Baby over the speedbumps without scraping and through the corners precisely! I have 5 on 5" lugs. The price sounds good to me also even though i have to save a few months for that! My adress is for shipping is: Kurze Minte 4 27321 Thedinghausen Germany Do you make the customs declaration and know about the quotes for that, or do i have to make hat here? Volker |
Re: No Limit Spy Photos
anything new that's ready to go
|
Re: No Limit Spy Photos
I might have missied it somewhere, but this is a bolt-in right?
Hey Rob, How about the same bolt-in setup for 67-72 F100's? Thanx Dano |
Re: No Limit Spy Photos
yes, it is a bolt in. - one thing at a time.
|
All times are GMT -4. The time now is 09:49 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com