My BBC couple pictures.
I finally got all the pistons in an went back an check clearances this weekend an all is well. Just though I would share. This has been a long time coming. Hopefully have the engine together sometimes in March.
http://i168.photobucket.com/albums/u...t/DSC_0200.jpg http://i168.photobucket.com/albums/u...t/DSC_0199.jpg http://i168.photobucket.com/albums/u...t/DSC_0119.jpg |
Re: My BBC couple pictures.
Looks good :thumbs:
Quite the dome on those pistons. What cubic inch are you building? |
Re: My BBC couple pictures.
ya kickin domes on those pistons, what heads are you using and what compression will it end up being with the chamber size.
|
Re: My BBC couple pictures.
Now were talking!
|
Re: My BBC couple pictures.
Specs?
|
Re: My BBC couple pictures.
Guys it is a 427 .030. GM steel crank, Callies rods, solid custom roller for my application an has been balanced. I will try an keep it updated. Went to put my my timing chain cover on it it would not fit right so I could set my camshaft end play. So going try an get time to work on that this week.
|
Re: My BBC couple pictures.
Quote:
The camshaft his suppose to be 2800-7000 and the heads are Brodix oval port RR's. Also have the Brodix valve covers. |
Re: My BBC couple pictures.
Sweet!
|
Re: My BBC couple pictures.
Thanks, it has been a long time coming. Going to work on it again this weekend.
|
Re: My BBC couple pictures.
Rat...this should have XXX next to the tag line!
Going to be good! |
Re: My BBC couple pictures.
Quote:
I try to do things right. Starting with this an get the truck right. I then may go to more cubes in a few years. I ditched the steel roller cam button for a nylon easier to set clearance with it. |
Re: My BBC couple pictures.
I sure would like to start on it again. But, it is 21 degrees outside an I am on call this weekend an worked half the night last night. I do not even feel like firing the heater up. So, it is going to wait I guess.
|
Re: My BBC couple pictures.
Got a little more done but no pictures will have some most likely this coming up weekend.
|
Re: My BBC couple pictures.
|
Re: My BBC couple pictures.
This thread and me getting my fab work done to my truck has me wanting to get my 496 back even more!!!!! :)
|
Re: My BBC couple pictures.
Very nice & clean!!
|
Re: My BBC couple pictures.
Thanks,
I am going to try an got the oil pump bolted in place an check its height one last time an then bolt the oil pan in place. Post a pick again tomorrow hopefully. I am on call this weekend 24/7. |
Re: My BBC couple pictures.
What oil pump are you using?
Posted via Mobile Device |
Re: My BBC couple pictures.
Quote:
I have always used the M77 an never had a problem. "So if it's not broke don't fix it". I heard the argument on both sides. I decided to go with what I know an have always done. |
Re: My BBC couple pictures.
I've used both and can only recommend the HV if you are running an oil pan with a capacity of 8+ quarts, this from experience of course.
|
Re: My BBC couple pictures.
Thats the thing on the Big block a little more pressure is better than the Hvolume pump and less of a power robber too.
|
Re: My BBC couple pictures.
Quote:
|
Re: My BBC couple pictures.
I have been kicking my self the last few months for not going with a std pump. I get little annoying leaks. Pushing 60psi when cold and around 45-50 when warm. I may replace mine soon.
|
Re: My BBC couple pictures.
I found that out the hard way too.:lol:
|
Re: My BBC couple pictures.
If I ever get my lazy butt started again. I am going to put the oil pan on.
|
Re: My BBC couple pictures.
Quote:
|
Re: My BBC couple pictures.
Yes that's the one I installed. That's the other the extra spring that comes with the M77 pump it's the high pressure spring.
|
Re: My BBC couple pictures.
Quote:
|
Re: My BBC couple pictures.
Thats funny I always use the M77 pump and only had the extra spring come with the small block pump not the Big block pump, the spring doesn't change volume though only adds some pressure which is alright on the BB. My BB idles at about 18psi operating temp with the M77 stock spring.
|
Re: My BBC couple pictures.
Quote:
I figure between 25-30 psi at idle an 65-80 on the other end with the HP spring. Of course it also depends on clearances. Was going to work on it this evening but worked over some an just did not have it in me when I got home. |
Re: My BBC couple pictures.
Did everyone see that nice looking timing cover? Well, it is coming off this coming week it will not match up with the Milidon oil pan. Then it is going back where it came from. Have a Milidon cover on the way. Should be here Tuesday or Wednesday this coming week.
By the way it is not a name brand cover. Told him I would try it. |
Re: My BBC couple pictures.
Well got the new cover in an it fits perfect. But, going to have to buy a another cam button. I have bought my last off brand timing cover. No pictures, but should have some middle of week or this coming weekend. I went to the round track racing last night for the first time in 15 years an it kind of got me stirred a little.
|
Re: My BBC couple pictures.
Well, could not find a cam button close to home. So, going to make a trip to the Speed Shop saturday an pick up one. He did not have any either. He said he would have some by this weekend.
|
Re: My BBC couple pictures.
Well my camshaft end play is set. Put the timing cover on.
|
Re: Picture update
|
Re: My BBC couple pictures.
I get to start on the top side this weekend.
|
Re: My BBC couple pictures.
Quote:
|
Re: My BBC couple pictures.
Quote:
|
Re: My BBC couple pictures.
As long as it's done and done right, stock chrome looks just fine!
|
Re: My BBC couple pictures.
Quote:
|
All times are GMT -4. The time now is 04:58 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com