70-71 Valve Cover Decal
 

Reproduction 8:350 valve cover decal found on some 1970 and 71 trucks. I had these reproduced for my own restoration building off the work of member Steve Hafner.

EDIT 3/27/23: I recently had the chance to get up close and personal with an original (almost completely) intact version of this decal. Since I've got a new build going, I took the opportunity to photograph it and revisit our reproduction. Our first attempt was based off old GM media and off angle pics of barely there survivors. This "Mark II" version is a much more faithful reproduction with regard to font and dimension. It looks like I can't delete the pics below without contacting an administrator. Just know that the pics below are of our first attempts and not the new better version.


Revised (Improved) Version $15 shipped

Thanks,

Brad

Re: 70-71 Valve Cover Decal
 

These look really nice. Were these made to withstand the engine compartment environment? As I understand it, these only go on the passenger side (I've seen other threads about this). Also, are the originals a sticker or a silk screened thin piece of metal with an adhesive backing. Akin to a an emblem.

Re: 70-71 Valve Cover Decal
 

Thanks. They do only go on the passenger side. They are discussed in a few threads here on the site. I am not sure about the construction of the originals, and have never seen one in person myself. My opinion is that they were "stickers" on par with the other decals in the engine compartment at that time. With regard to the heat resistance of these decals, I cannot say with certainty. I had a long conversation about this with the printer during the planning stages and the most heat tolerant stock that matched our design requirements was chosen. I have 180 miles on my Blazer (all in summer in Georgia) since completion and it shows no signs of degradation or release at this point.

Re: 70-71 Valve Cover Decal
 

I'll take one of the "final" versions. PayPal ok, or do you prefer another method? Thanks- Ryan

Re: 70-71 Valve Cover Decal
 

PM sent.

Re: 70-71 Valve Cover Decal
 

Payment sent, thanks again!

Re: 70-71 Valve Cover Decal
 

I will take one, 'final' version.

Re: 70-71 Valve Cover Decal
 

PM sent.

Re: 70-71 Valve Cover Decal
 

I'll take one, final version.
Thanks

Re: 70-71 Valve Cover Decal
 

Ill take 2 final and one beta. could you adjust shipping? Thanks

Re: 70-71 Valve Cover Decal
 

PMs sent.

Re: 70-71 Valve Cover Decal
 

if you still have them I will take 2 of the final version.
pm with paypal info
thanks phililp

Re: 70-71 Valve Cover Decal
 

PM sent.

Re: 70-71 Valve Cover Decal
 

payment send for a pair of the final versions
thanks
philip

Re: 70-71 Valve Cover Decal
 

Thanks. I'll put them in the mail tomorrow.

Re: 70-71 Valve Cover Decal
 

Decal arrived this morning. Absolutely beautiful!

Re: 70-71 Valve Cover Decal
 

Awesome!

Re: 70-71 Valve Cover Decal
 

3xt.

Re: 70-71 Valve Cover Decal
 

. . . .

Here's the one on my C-10 . . . about two hundred miles on it too and still there !!!

. . . .

Re: 70-71 Valve Cover Decal
 

It looks great Steve...like it was made for it;) Thanks for the pic.

Re: 70-71 Valve Cover Decal
 

Do u have any more final version

Re: 70-71 Valve Cover Decal
 

I'll take a final version if still available.

Re: 70-71 Valve Cover Decal
 

Yes I do.

PM sent.

Re: 70-71 Valve Cover Decal
 

PM sent.

Re: 70-71 Valve Cover Decal
 

Thanks for doing these, I would like to purchase 2 final versions.

Re: 70-71 Valve Cover Decal
 

PM sent

Re: 70-71 Valve Cover Decal
 

I had run out of "final" versions, but due to continued requests for these and the Blazer Jacking Instructions Decal, I did another limited run. So I have a few more of these available.

Re: 70-71 Valve Cover Decal
 

take a final -paypal

Re: 70-71 Valve Cover Decal
 

Sent a while ago(as you know)...just wanted to reply in thread. It looked like I'd left you hanging.

Re: 70-71 Valve Cover Decal
 

3xt

Re: 70-71 Valve Cover Decal
 

Just to pile on, these are super nice and if you are looking to be correct on your stock restoration, look no further.

Re: 70-71 Valve Cover Decal
 

Subscribe.......put me down for 2 when you do another production run.

Thanks
Jim

Re: 70-71 Valve Cover Decal
 

You bet.

Re: 70-71 Valve Cover Decal
 

I guess I kind of missed this post. Thanks for the comment Harold. Been a big fan of your work for a while...especially the SWB K10 Super...creme dela creme.

Re: 70-71 Valve Cover Decal
 

I wish you or someone would make the 72 version that came on the passenger side valve cover. It was like a thin piece of aluminum foil with adhesive on the back.

Re: 70-71 Valve Cover Decal
 

Do you have a pair of the $10 ones left ,if so I would take them if I can mail a money order .I think they would look good on my coffee table project.

Re: 70-71 Valve Cover Decal
 

Definitely have Beta versions left. PM sent.

Re: 70-71 Valve Cover Decal
 

PM returned ,will get patment in the mail .
Thanks John

Re: 70-71 Valve Cover Decal
 

I missed these somehow. Do you have any final versions left? I need one but would take 2 if available. Nice work!

Re: 70-71 Valve Cover Decal
 

Sorry John..been out of town...still am in fact. Will get yours in the mail on Monday.

No finals at this time. Considering another run. Betas available right now.