Revolving cup holder pics
 

A few people on the parts forum asked where I got these and I couldn't remember (I got them a few years ago) but I just found a match on ebay. This apparently came from a 95-98' Windstar but I don't ever remember being in of those vans. If you remove the ashtray this fits right in the opening perfectly. You will need to secure it with screws which shouldn't be too hard if the heater controls are moved out of the way. Here are a few pics without it being painted to match the dash. I've decided to keep looking for something different. Here are a few pics of this relatively easy mod!

Re: Revolving cup holder pics
 

wow!!!

Re: Revolving cup holder pics
 

Clever! Since my ashtray is filled with hardened gum, I may have to do that little trick.

Re: Revolving cup holder pics
 

Will a Modelo Especial fit in it?

Re: Revolving cup holder pics
 

Not sure Tim, but a Slurpee will:lol:

Re: Revolving cup holder pics
 

Now I am thinking....If I were to take the ashtray front and trim the center to accept this cup holder, then mold the two together so it would be as flush and invisible as possible and paint it to match.....it would look REALLY good. (Not saying the way you have it doesn't, but you can almost camoflage it into the original ashtray front.)

Re: Revolving cup holder pics
 

That would actually be pretty easy to do. Good idea!

Re: Revolving cup holder pics
 

Maybe even make the ashtray front flip down and have the cup holder behind it. That would be pretty stealth too. I like the cup holder...I guess it's time to watch ebay for some :D

Mike

Re: Revolving cup holder pics
 

I got one I will donate if you wanna try it ;)

Re: Revolving cup holder pics
 

You need me to PM you an address? I have to hit the junk yard on Saturday anyway to look for a part (for my dad's truck), so I will look for the correct minivan while I am there.

Re: Revolving cup holder pics
 

here 'tis

http://cgi.ebay.com/ebaymotors/1996-...spagenameZWDVW

Re: Revolving cup holder pics
 

Yeppers, you want my OE one or my Chrome one?

Re: Revolving cup holder pics
 

I like the way you are thinking but, with the ashtray front attached to the front of the rotating cup holder, how would it rotate?

Re: Revolving cup holder pics
 

You would have to cut out a rectangle in the face of the ashtray for the rotating part. You would probably also have to remove the ashtray part from the face and discard it because I don't think it will fit vertically otherwise. Basically you would reuse only your ashtray face, cut a rectangle out for the rotation and the perimeter would still look stock. A dremel with a cutoff wheel and a little patience should do the trick!

Re: Revolving cup holder pics
 

i have to say that cup holder is amazing, altho i dont think i would notch the dash to put the ashtray face on it, just me tho

Re: Revolving cup holder pics
 

I'd like to see what could be done...but for now I'll stick with putting my Jumbo Soft Drinks between my legs while I drive and keep freezing the "boys", I hear it's good for 'em anyway... :lol:

Re: Revolving cup holder pics
 

No notching of the dash would be necessary.

Re: Revolving cup holder pics
 

Exactly. We need a photoshop guru to install this into an ashtray cover.
Anyone have a good photo of an ashtray front?
Then we can post it on the photoshop board.
LUV, I will PM you my info.

Re: Revolving cup holder pics
 

Using the ashtray face is a good idea,but!From the pivot point of the cup holder the face plate of the ashtray will hang over not letting it rotate.A flip down Idea may be more practical just need to come up with a hidden hinge.

Re: Revolving cup holder pics
 

There was a member that hinged a radio delete to cover his radio. I don't think he is willing to give up his idea. Maybe someone else has an idea for a hinge.

Jason

Re: Revolving cup holder pics
 

Your idea would work,just cover it and cut out the center.

Re: Revolving cup holder pics
 

Yep. Have it rotate out of the ashtray face INSTEAD of the black plastic surround. And then color it to match the rest of the ashtray face.
Similar to this. I wish I was a Photoshop user so I could make it look right and color it!!! But this is the basic idea.
ONLY the cup holder rotates...NOT the ashtray face. It is fixed in position.

And, 70C10, please don't think that we are not impressed with your idea and install. It is a GREAT idea and you did a fine job. After re-reading this post, it looks like we might be bordering on picking it apart. Sorry, that is not the direction we are taking...HONEST!!!

Re: Revolving cup holder pics
 

I didn't take it that way at all Putter!. It looks like you and me are are the only ones on the same page with this rotation and your photoshop is what I was trying to describe exactly. Hopefully your pic helps make it clear. You are the man dude!

Re: Revolving cup holder pics
 

Nice work!

Re: Revolving cup holder pics
 

If I'm not on the same page, at least I'm in the same chapter. It just takes me a while to conceptualize another mans ideas without the ability to lay my hands on the components. I've got a Windstar cup holder on the way now, so I get to play too.
What is the height of the rotating member?