The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1960 - 1966 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=6)
-   -   Picture needed PLEASE! (https://67-72chevytrucks.com/vboard/showthread.php?t=327958)

buster0104 02-09-2009 05:16 PM

Picture needed PLEASE!
 
I finished the disc brake conversion today. Well almost. I wanted to swap the centerlink also. Everything came off a 71. My question is where do I drill the holes at in the frame? I bolted up everything. Tie rod ends, Hooked up the steering on the drivers side. Then hooked up the tie rods on the passenger side. The arm (don't know what it is called) that bolts up to the frame is way different than my 63. I have seen this swapped over and was told that you had to drill some holes. I hope I have explaned what I need well enough. Any pictures or info will be very helpfull. Thanks Dustin

Joey~AP 02-09-2009 05:24 PM

Re: Picture needed PLEASE!
 
Pitman arm?

buster0104 02-09-2009 05:43 PM

Re: Picture needed PLEASE!
 
1 Attachment(s)
This is what I'm talking about. Not sure what it is called. Please help!
Attachment 429121

protrash64 02-09-2009 06:02 PM

Re: Picture needed PLEASE!
 
That is a drag link, I believe.

maximum destruction 02-09-2009 06:36 PM

Re: Picture needed PLEASE!
 
that's an idler arm.

protrash64 02-09-2009 07:00 PM

Re: Picture needed PLEASE!
 
Quote:

Originally Posted by maximum destruction (Post 3134351)
that's an idler arm.

yeah, there you go!!!:lol:

buster0104 02-09-2009 08:08 PM

Re: Picture needed PLEASE!
 
It doesn't bolt up where the original one does. Witch I knew that. But how do I know where to bolt it up at. I know that I will have to drill new holes. But I don't want to drill a bunch of holes to figure it out. If someone has done this, could you direct me in the right direction?

Wolfinthesnow 02-09-2009 08:30 PM

Re: Picture needed PLEASE!
 
I put a 76 front under my 63. Regretably, I cant remember where the holes were drilled. We used a couple of c-clamps to determine the best mounting spot. Enough room around my place to test drive. Very slowly of coarse, and not very far. Just enough to make sure everything was tracking correctly. Just my .02.

buster0104 02-09-2009 09:01 PM

Re: Picture needed PLEASE!
 
Thanks Wolf. I didn't think about that. I'll give it a try.

Alan's Classic 02-10-2009 12:16 AM

Re: Picture needed PLEASE!
 
Quote:

Originally Posted by maximum destruction (Post 3134351)
that's an idler arm.

:agree:

I leveled my frame from side to side. I then leveled the center link and measured from crossmember to get it even then clamped the idler and drilled.

http://i369.photobucket.com/albums/o...d/DSC08237.jpg

buster0104 02-10-2009 12:50 AM

Re: Picture needed PLEASE!
 
Thanks Allen! I just found a post where you were doing the same thing and reread you whole build thread. Again. Your doing a great job. Thanks for all the help guys. Guess I will give it a try soon. Dustin

ron19 02-10-2009 01:27 AM

Re: Picture needed PLEASE!
 
2 Attachment(s)
Quote:

Originally Posted by Alan's Classic (Post 3135133)
:agree:

I leveled my frame from side to side. I then leveled the center link and measured from crossmember to get it even then clamped the idler and drilled.

http://i369.photobucket.com/albums/o...d/DSC08237.jpg

I did the same thing. Someone on the board was nice enough to post this pic of their idler arm mount for me and then I put mine on in about the same place and levelled everything out. Unfortunately, I only have the steering box view of mine, I could get the other side if you need it, it's much like this one posted.

buster0104 02-10-2009 01:40 AM

Re: Picture needed PLEASE!
 
Thanks ron19. That 2nd picture is exactly what I needed. How did it work out for you? Any problems?


All times are GMT -4. The time now is 11:43 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com