kustom center console
 

so thursday i decided i wanted to go a different way with my dash so friday i thought i would make a center console for my radio and a catch all spot so i got some card board my exacto knife and some trusty ole duck tape headed down to truck to make a template heres what a couple of houres turned out

Re: kustom center console
 

more

Re: kustom center console
 

so taday me and a couple of buddys decided to start making it and this is what i have now just need to figure out if im going to carpet it or something else

Re: kustom center console
 

some more

Re: kustom center console
 

That's pretty sweet! Only thing I feel is radio wouldbe heck to reach from the drivers seat, but I like it!

Re: kustom center console
 

i got a remote to solve that prob lol

Re: kustom center console
 

would you mind posting the measurements on that you did a hell of a job.

Re: kustom center console
 

I think we should all be doing something like this so we have a place to put the aftermarket radios without hacking up the instrument panel. I have seen custom consoles like this with the upper front portion a little higher (actually rising above the bottom of the dash, about next to where the original radio location would be) and angled up and toward the driver a little for easier access. Also have seen the radio mounted vertically, pointed up toward the roof, next to the driver, but I didn't care for that much. This looks like a good plan. The radios in a headliner shelf look handy also, but a little too much like 10-4 rubber ducky CB radio for me.

Re: kustom center console
 

looks great bro!

Re: kustom center console
 

nice to see I'm not the only one building stuff from cardboard and duct tape...lol...check my build I did a center consol put my amp and a 10" sub in it along with the radio and the controls for my air ride...I used a radio delete panel and put my 2 air ride guages into it which is nice since I didn't cut te dash at all....

heres a link
http://67-72chevytrucks.com/vboard/s...51#post3800951

Re: kustom center console
 

hottrucks i like yours too if i kept my buckets i would of added in my 12 and amp but got two kids so the buckets went for a bench when the get older i might go back and as far a mesurements wigglestheholly what do you want overall or specifics just let me know

Re: kustom center console
 

I know what you mean if you look at my early build pics I had the stock bench and built a short consol the was even with the top of the seat...I used that consol for a template to make it longer when I switched to buckets..( Dumb Move I like the bench better)

Re: kustom center console
 

Re: kustom center console
 

Both my consoles follow the trans hump and is kinda wedged under the dash they are pretty tight fit too...

Re: kustom center console
 

Looks good. Hope your little one doesnt kick the faceplate off that head unit though.

Re: kustom center console
 

as far as hold down when i figure out what the final covering is going to be im going to use some l brakets and screw them to the trans tunnel for now its wedged in ther pretty good and both kids arnt big enough to reach it yet

Re: kustom center console
 

you seem to have the glass thing down...I would run a router around the edges and glass it all..then paint it or take it to a local boat shop and have them gel coat it any color you want..a couple pieces of carpet along the bottom wil take care of the kick marks you can get a piece of carpet and have it seamed cheap at most carpet places

Re: kustom center console
 

heres some mesurments its made from 1/2 inch mdf its 10 inches total across its about 15 1/2 inches lomg and 9 inche tall at the point if need more just say

Re: kustom center console
 

Looks great! Definitely be sure to bolt it down though... I found out what a wooden console with sharp edges does when you roll your truck and its not bolted down very well... I had a couple a punctures to the bone from the sharp edges on the box. They never did find the console though.....

Re: kustom center console
 

so i finally decided to carpet it got some from a friend that had extra dont think it came out to bad for never doing it before the cup holder section was a real pain but its a rat rod not supposed to be perfect

Re: kustom center console
 

I like it!. It reminds me of a vega that was covered in carpet.

Re: kustom center console
 

Question? Is your lower vent still free flowing or is it now obstructed with your console?

Looks good!

Re: kustom center console
 

no its not blocked

Re: kustom center console
 

what I did was cut a piece of the aluminum flexable tubing on the side so it fits over the stock heater ports and ran the 2 opens ends out a cut out near the front to blow on your feet..works well ..just need to notch out for the piping

look at pic # 15 on this post you can see it on the pass side I have since squirted it with some black paint so you dont see it as badly
http://67-72chevytrucks.com/vboard/s...51#post3800951

Re: kustom center console
 

looks nice
we did a console for amps and radio & tv. We held it down with two angle brackets on each side. We also added two computer fans to keep the amps cool. Covered it with vinyl.
http://67-72chevytrucks.com/vboard/s...=320658&page=3
Don't mean to hijack your thread.