Parting out 76 Blazer
 

I picked this one up a while back and I'm using some of the parts for my 78 Blazer, but would like to sell off all of the parts that I'm not using. I will be using the engine, front and rear bumpers, bucket seats, tailgate band, and some other small parts. I accept post office money order or paypal...you cover fees. The roof is rusted out on the tub so I will sell patch panels from the tub starting at $25 plus shipping.
bare frame...$200 local
hard top...$100 local
th350/np203...$100 local
fender emblems...$30 shipped
dash emblem...$13 shipped
spare tire tailgate bracket...$22 shipped
15x8 6 lug ralley wheels (4)...$100 plus shipping
transmission skid plate...$32 shipped
Please ask if there are any parts you need.
Thanks,
Ray

Re: Parting out 76 Blazer
 

more pics

Re: Parting out 76 Blazer
 

How do the rims look Ray?
How much for the front axle? Gear ratio?
Also could use some square gas cap doors cut out with the bed portion if you have any two tank setups. I need them to repair a bed that has aftermarket fuel doors on it. You coming out this way anytime soon? Frank

Re: Parting out 76 Blazer
 

Do you have the linkage that went from the column inside the engine compartment to the transmission?
Posted via Mobile Device

Re: Parting out 76 Blazer
 

Ac lines?
Posted via Mobile Device

Re: Parting out 76 Blazer
 

Frank, I have several sets of those wheels. I can pick out the best ones for you. The front axle is 3.07 gears...$100. I have 2 good gas doors/patches from an 81 for $20 each.
Johns66, $32 shipped for the at linkage.
Frog, Sorry, no good ac lines.

Thanks,
Ray

Re: Parting out 76 Blazer
 

I have a 76 k5 so i would be interested in alot of things off this truck
bolts for removable cap, any of the guts to the doors and tailgate,

Re: Parting out 76 Blazer
 

Let me know what you need.
Thanks,
Ray

Re: Parting out 76 Blazer
 

so bare frame local, how bare? I could use some front leaf hangers for the front axle.

Re: Parting out 76 Blazer
 

I have a pair of hangers pulled from a 78 GMC 3/4 ton 4wd that should work good for you. $66 shipped. I will carve up the frame so they can fit in a large flat rate box with usps.
Thanks,
Ray

Re: Parting out 76 Blazer
 

how are the 2 chrome pieces that go where the top bolts to the body

Re: Parting out 76 Blazer
 

Ill buy the cap bolts, both door guts/insides lock rods latches, bolts etc. Also tailg.ate guts/insides
im also looking for a frame crossmember
Posted via Mobile Device

Re: Parting out 76 Blazer
 

door panels? do they have wood grain?

Re: Parting out 76 Blazer
 

I'll have to pass then I'm trying to find a set real cheap for my sas project and I can order some universals for cheap. I was just hoping to find some stockers for cheaper.

Re: Parting out 76 Blazer
 

Hi Ray:

Does that '78 GMC have good front hangers for the rear springs? I need the hangers and the back part (support) for both sides. The ones on my K20 were so bad I cut them off so I wasn't tempted to drive it. Thanks

Re: Parting out 76 Blazer
 

I will check to see if I have some laying around. That frame went for scrap already.
Thanks,
Ray