Parting a 72 C20 very original truck
 

Ask questions in thread
I'm hopefully going to start parting this Fri night some and then this weekend if I have time, don't be in a big hurry, I have a real job, wife and kids
Pay pal with fees or money orders
I ship fed ex and USPS
outer grill $100, no ship 29od1 has first shot at it
PS pump/brackets, motor pullies, alt brackets are SOLD already
booster setup $80 shipped
AT linkage $38 shipped
column $75 shipped
shroud $75 shipped
sway bar $75 shipped
front fenders have some small rust, I think rad support is good. Pass door is decent. Cab has all low rust. Driver door is bad. Bedsides are that bad, bedfloor is wavy.
see anything else and I will get pics and price

Re: Parting a 72 C20 very original truck
 

53

Re: Parting a 72 C20 very original truck
 

58

Re: Parting a 72 C20 very original truck
 

63

Re: Parting a 72 C20 very original truck
 

Front bumper- Price? Condition?
I'll take the outer grill if 29od1 passes

Re: Parting a 72 C20 very original truck
 

Do i see an original cig lighter in that truck, Just the part ya pull out to light the cig.

Wires out of the seat cover??

Re: Parting a 72 C20 very original truck
 

Carb with choke assembly and bolts to 30094?

Re: Parting a 72 C20 very original truck
 

Price for ash tray with slider and complete brake pedal and accelerator pedal set up with bracket to 87124? Thank you.

Re: Parting a 72 C20 very original truck
 

I'll take the sway bar

Re: Parting a 72 C20 very original truck
 

Just air cleaner with OE rod and wing nut that mounts in Carb

Re: Parting a 72 C20 very original truck
 

I need a 71/72 Driver side parking light housing, a tail light housing with screws, and two reverse light housings.

If these are all in good usable condition not real rusty can i have a price on them shipped to 11937 please?

Re: Parting a 72 C20 very original truck
 

Hi Randy,
I'll take the grill and headlight bezels.
Thanks,
David

Re: Parting a 72 C20 very original truck
 

Bonesaw, front bumper is nice, $60 plus shipping without lights

Swamp rat, Mike, for male part of lighter another $10 and I can put it in with other parts

Uncle, $45 shipped for carb and choke

72chevyss, slider is welded in on ashtray, I cut out whole center radio section, $25 for all with ash tray. Brake pedal is $20. gas pedal, with throttle cable and carb bracket is $35, all plus shipping

1stchevy, sway bar is yours, it will probably need new rubber bushings

David Passmore, $25 plus shipping for air cleaner and rod and wing nut

yfs200p, turn signal housing is $15, are you needing both tail light housings and both reverse light housings, if so $20 for all 4, and shipping

David, it does have a couple small dings and scratches. One spot on lower pass side is wore through. I'll get better pics

Thanks Randy

Re: Parting a 72 C20 very original truck
 

Is the auto column and linkage for a C20 the same as the C10? Any idea of the condition of the column, not concerned about aesthetics, just the mechanics. Price shipped to 29621 for the column, shift linkage from column to trans and the frame pivot, assuming all of this would bolt up to a C10?

Re: Parting a 72 C20 very original truck
 

I'll take the front bumper. 80401.
Im still in for the outer grill 29od1 passes.

Re: Parting a 72 C20 very original truck
 

I'll take carb. Pm payment info.

Re: Parting a 72 C20 very original truck
 

I'd like to get in line behind clemsonteg for the steering column and wheel, and shift linkage. I am also more concerned with mechanics than anything. Price shipped to 59823. Thanks

Re: Parting a 72 C20 very original truck
 

take 25 shipped for the air cleaner ??

Re: Parting a 72 C20 very original truck
 

I'll pass on the ash tray. What will shipping for the brake pedal and accelerator pedal with bracket be to 87124?

Re: Parting a 72 C20 very original truck
 

Randy,
Nice find...
Ill take the turnbuckle thing on the rear bumper if youll throw it in my box of stuff for a few dollars extra.
I see your taking Paypal again, can I send you the money that way? If not Ill get it mailed today. Been busy lately...

Mike

Re: Parting a 72 C20 very original truck
 

The 2 inside door scews and furrels ( the ones that are inside under the wing windows that hekp hold the door together) and the bench seat bolts. Ship 90631

Re: Parting a 72 C20 very original truck
 

I would be interested in exhaust heat riser shield and tube.
Thanks
Rock C

Re: Parting a 72 C20 very original truck
 

Roger!

Re: Parting a 72 C20 very original truck
 

Randy how are the defroster vents? How is the brake booster?

Re: Parting a 72 C20 very original truck
 

clemsonteg, sold the column locally this morning. I still have the AT linkage

Bonesaw, sorry I also sold the bumper locally to another guy this morning. Sorry I don't ship grills

Uncle, carb and choke are yours

jaybatta, sorry column is sold locally. I have the linkage still

1967chevytruckguy, no sorry, shipping alone would be $15 atleast, and I have to get D.Passmore a quote on it

72chevySS, I'll get it all off and a quote, hopefully this weekend

Mike, THANKS, got lucky. I'll get with you no worries on sending it in mail

John in Socal, $20 shipped for all that

RockC, your first on it, let me get it off and check condition

David, I'll get you a quote

BB72chevkt, $15 plus shipping for the best one

Littletony, I'll have to check defrost vents. On the booster, the brakes work with it not running but sorry I don't guarantee boosters

Everyone, As I said above, I'm going to try to start parting this truck some Fri after work and some Sat, I have another truck to go pick up that I have sold already. Plus some guys coming to get some parts, so not sure how much time I will have till next Mon night

Thanks Randy