The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1960 - 1966 Chevrolet & GMC Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=6)
-   -   The little things !! (https://67-72chevytrucks.com/vboard/showthread.php?t=688574)

scottco 11-14-2015 07:39 PM

The little things !!
 
1 Attachment(s)
Did a little clean up today. Also got carpet in and heater all done and working. Cleaned up some wiring under the dash. Trying to get up the nerve to order the 700r4 transmission to replace the powerglide... lol ..
Any recommendations on a transmission supplier?

TJ's Chevy 11-14-2015 08:00 PM

Re: The little things !!
 
Bought my Tremec from Summit Racing. Never had problems with their service. Truck looks good! :chevy:

T.W.Dustin 11-14-2015 09:18 PM

Re: The little things !!
 
Good looking truck! Go with someone you trust on the trans, it isn't anything that different so lots of options out there.

WOLFMANmike 11-14-2015 11:07 PM

Re: The little things !!
 
[QUOTE=scottco;7376343]Did a little clean up today. Also got carpet in and heater all done and working. Cleaned up some wiring under the dash. Trying to get up the nerve to order the 700r4 transmission to replace the powerglide... lol ..
Any recommendations on a transmission supplier?



http://www.bowtieoverdrives.com/ here is a bit of infor for you to before you buy the 700r4 with a 700r4 you have to do things like shorten the drive shaft and make other mods to get one in and also the shift from 1st to 2nd is such a long drop in rpms i really dont much car for it kinda feels like a slosh box to me . but if you go with a 200 4r its the same length as your power glide so no shorten of the shaft and the it shifts like a TH 350 dose and 4th is still a great over drive they can be built nasty if need be as you will see on this site .. i had 200 4r in my old Chevelle 383 stroker 400 + HP and its took a nasty beating i would say this is the best bang for your buck and to go to these people

Clyde65 11-14-2015 11:15 PM

Re: The little things !!
 
Where in Texas are you? If in the dfw area, i can pm you a member here and a very good shop. ( he works there)

Captainfab 11-15-2015 01:35 AM

Re: The little things !!
 
I agree with having a transmission built locally if at all possible. It is much easier to deal with should a problem arise.

scottco 11-15-2015 11:07 PM

Re: The little things !!
 
Thanks for all the info... Time to shop..

verdell 11-16-2015 12:53 PM

Re: The little things !!
 
Yes, go with a local builder. I got burned by "reputable shop" away from my area. Took my 700r4 to this shop 3 hours away and had it built to handle power. Brought it home, installed and the thing wouldn't move. Spoke with the owner over the phone and took it back. They "went through it" again, brought it back home and installed...same thing, wouldn't move. Went BACK to the transmission shop and the building was closed with a "for lease" sign on the door. Very expensive lesson. Heaven forbid I run into any of those guys again...

SS317 11-16-2015 03:28 PM

Re: The little things !!
 
I pulled out my powerglide and installed a 700R4. I love the change and the drop from 1st to 2nd isn't too bad for me.
I did a lot of research on this site and took notes. I then went to three local shops and started asking questions. The shop I chose was answering the questions on my list before I even asked them, so he knew exactly what was needed to get the job done.

Love the mod, go for it.

Clif Dzzzz 11-17-2015 12:52 AM

Re: The little things !!
 
We would line to see your list of questions.....I might be in same boat....

Chevy Fleetside 11-17-2015 01:49 AM

Re: The little things !!
 
What do I love about the 700R4. Today crusin down the freeway at 80mph taching 2300 rpms. 3.08 rear with 28" tires. All this behind the BB.

SS317 11-19-2015 02:17 PM

Re: The little things !!
 
Quote:

Originally Posted by Clif Dzzzz (Post 7378926)
We would line to see your list of questions.....I might be in same boat....

Dig into the threads for the questions. Things like, the stock column shift won't go to 1st gear, transmission cross member, Cutting the drive shaft a little, TV Cable adjustment bracket with your existing carb. There are things you need to know before you go into the tranny shop.


All times are GMT -4. The time now is 01:13 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com