Where do I cut this fender?
 

I'm going to be starting the repair of this passenger side front fender cup, and I'm curious where to make the cuts on the original fender. Should I keep the replacement part whole and cut the fender to fit it, or should I only cut the rust off the fender, then trim down the patch panel to fit?

http://i.imgur.com/Y7m24GE.jpg

After looking at the backside, it looks like the bolt-holes in the patch panel would make a nice place to take measurements from, then transfer those measurements to the original fender.

http://i.imgur.com/mf5AEVc.jpg

Any thoughts or experience is appreciated. (Sorry for the blurry pics, I'm not sure how that happened.)

Re: Where do I cut this fender?
 

I'd cut it just below the body line if possible

Re: Where do I cut this fender?
 

Others will chime in but I would run a tape line about 1/2 " below the strait body crease and trim the fender there. Tape the patch piece 1/4" below the strait body crease and tuck the 1/4" extra of the patch piece under the fender. Some trimming of each end may be necessary as they will not tuck.The ends will be a butt weld but the rest will be over lap. Now that I have probably confused every one it is easier to show than to explain.I have done restoration for over thirty years but I am a better doer that teacher. I also assume that you may not have a punch/flange tool. Take careful measurements and you should do fine.

Re: Where do I cut this fender?
 

This is where I would cut it so you have easy access to weld and hide with filler.

Re: Where do I cut this fender?
 

I agree with the posters above. about 1/2" below the bodyline

Re: Where do I cut this fender?
 

Definitely do not cut fender to match part dimensions. Cut part to meet the fender cuts.

Re: Where do I cut this fender?
 

Thought I'd update this thread to show how it worked out. I used a piece of masking tape to bring the body line down 3/4" and made the cut. It worked great!

http://i.imgur.com/aAPAmrj.jpg

Here it is in primer. Needs a little filler on the weld joints, but otherwise pretty good.

http://i.imgur.com/J8CQji0.jpg

Thanks again for the help!

Re: Where do I cut this fender?
 

Looks good

Re: Where do I cut this fender?
 

Looks good but may I ask how you ended up with a vertical weld also ?

Re: Where do I cut this fender?
 

Looks really good! The vertical cut is to "stretch" the repair cup- they're to short

Re: Where do I cut this fender?
 

looks good. I just went through the exact same thing. I ordered 2 cups from 2 different venders and both were to short. I had to lengthen mine just like yours. Also make sure that it fits in the front core support I had to do some cutting on the inside pocket to fit the support correctly.

Re: Where do I cut this fender?
 

I cheated a little on the fender cup, and I just cut the front and separated it and welded it back together to "fix" the short cup. The contour is different, but you cannot tell it, plus it's behind the bumper.

Re: Where do I cut this fender?
 

It turned out pretty good.

Re: Where do I cut this fender?
 

It looks like you had to make some extra slices too.

I tried to use as little as possible because it fit like tee total crap.

http://67-72chevytrucks.com/vboard/a...1&d=1486948251

http://67-72chevytrucks.com/vboard/a...1&d=1487560122

But I now have a solid fender that fits.

http://67-72chevytrucks.com/vboard/a...1&d=1487560122

Re: Where do I cut this fender?
 

I cut mine where the factory molding on my '68 goes instead of using the whole piece. As far as front to back, I just cut the from radius loose from the backing and made up the distance with one cut on the rear. The molding covers all but just a few inches on the front behind the bumper when installed.

Re: Where do I cut this fender?
 

I was actually referring to the OP :)

It looks like he had to split his horizontally and vertically.

Re: Where do I cut this fender?
 

Just for the record... tooling still hasn't been fixed on the fender cup patches. It's about 1/2" too short. The second picture is a cup from another stock fender. Both were cut about 1" below the body line.

Re: Where do I cut this fender?
 

This is a Good thread.
Very good input from OP and others.
I have been subbed for Awhile.
Glad to see it brought to the top.


Those are good reference pictures.
I hope to fix mine soon.



.

Re: Where do I cut this fender?
 

Please note that you must be a supporting member to post classified items. This includes but is not limited to What Its Worth, Want To Buy, Want To Trade, and For Sale. Please consider supporting the forum by subscribing. Further information on the subscription levels available are located here

If you need any further assistance with that please contact any Admin for help.

Re: Where do I cut this fender?
 

Wow,I have to pay to post for an item I'd like to buy?
Never had to do that on the other forums that I'm registered on.
Think I'll go to another forum.
Thanks.

Re: Where do I cut this fender?
 

In the for sale area there is no problem with you buying anything listed for sale and not being a subscriber. You cant list an item for sale or list a specific request to buy something if you are a non subscriber.

All sales on the board are supposed to go through the for sale area to avoid bad deals and shady happenings that used to happen before that rule was implemented years ago. So no sales or WTB's in other areas of the board whether you are a subscriber or not.

Re: Where do I cut this fender?
 

Not true. You can go to the the classifieds and buy what you need there. No charge other than the purchase price. It’s pretty cool how that works.

I type too slow.:lol:

Re: Where do I cut this fender?
 

It's called "paying to subscribe" so you can initiate a sale and we have a parts forum intended for just that purpose, not here. It's been that way since '05 or so, way before you clicked "agree" to the board policies in Oct '13 six years ago. Since this is the largest online community for the ever popular 67-72 GM Trucks in the world, and the first search result for such, we have been targeted by scammers who would pop in, list a few items for sale, money sent to them, then it's seeya! By requiring a mere $25 a year subscription (6 mo. term available for less) it has worked quite well to curb such activity. Those guys tend to go to those other sites you seem to hold in such high regard. You are welcome... to stay, but if you really feel that strongly about leaving, all I can say is have at it. Why not stick around and keep an eye on the parts board. But I suggest you go back and read the terms you agreed to before you run into any more surprises.

Re: Where do I cut this fender?
 

Can you show pictures of how to fill or stretch the patch panel with a cut to make up for that 1/2"?

Re: Where do I cut this fender?
 

Here is how I recently did this about two weeks ago on the 68 Second Chance Build. Had to add additional 1/2 of material on both sides of fender cup. One of the things I did that made it easier to work on was tack weld a small temporary piece of metal on the bottom so that it would not twist or change in size. You can see it in the first two photos.