The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=4)
-   -   PTO swap question (https://67-72chevytrucks.com/vboard/showthread.php?t=822159)

Jmoney01 05-26-2021 06:05 PM

PTO swap question
 
I am putting a nv4500 in my 1980 1 ton. I swapped the unit from the old 465. Problem is, the nv4500 housing is larger and will not allow the drive shaft to bolt up to the pto. Do they make different PTO units that space this out farther? Is there a different solution?
Thanks guys

kipps 05-26-2021 06:35 PM

Re: PTO swap question
 
I will admit, I didn't think the pto units would be compatible between a sm465 and a nv4500. Make sure that the gears are definitely compatible before you run it, otherwise you'll ruin both the transmission and the pto unit.

v30crewcab 05-26-2021 10:26 PM

Re: PTO swap question
 
yes they take different internal gears. and they have different offset housings as well. also depends on what year your nv4500 is. the early and late ones take a different gear too. one is 25 teeth I believe and the other is 30, due to the different 1st ratio. I have one off a 92-93 nv4500 here, but its only touching half of the tooth as it needs a 30 tooth gear in it. I was mocking it up to see if it would work but it won't.

Jmoney01 05-27-2021 05:29 AM

Re: PTO swap question
 
I'm not positive on the year of transmission. Tag on top, correct?

sweetk30 05-27-2021 07:01 AM

Re: PTO swap question
 
Shifter tower style help id it .

Early is pop in like 465

Late is 4 bolt newer style .

As said you NEED the correct pto parts for the change over from trans to trans .

Jmoney01 05-27-2021 09:08 AM

Re: PTO swap question
 
The shifter itself is not bolted in, it's like the 465

1976gmc20 05-27-2021 05:51 PM

Re: PTO swap question
 
Wow, I must have been lucky!

Almost 40 years ago I bought a PTO out of the junkyard and slapped it on an SM420 and it worked just fine :)

Dodgeguy1942 06-27-2021 06:30 PM

Quote:

Originally Posted by Jmoney01 (Post 8925278)
I am putting a nv4500 in my 1980 1 ton. I swapped the unit from the old 465. Problem is, the nv4500 housing is larger and will not allow the drive shaft to bolt up to the pto. Do they make different PTO units that space this out farther? Is there a different solution?
Thanks guys

are you interested in selling the pto
Posted via Mobile Device

Jmoney01 06-29-2021 09:39 PM

Re: PTO swap question
 
Sure

kwmech 06-30-2021 01:09 AM

Re: PTO swap question
 
I've got a brand new PTO and kit for an early 4500 that I never used. Current orientation is Left side rear facing. I was going to install the 4500 in my tow truck replacing the 465, but I ended up selling the truck before install.

kipps 06-30-2021 07:29 AM

Re: PTO swap question
 
Quote:

Originally Posted by kwmech (Post 8938410)
I've got a brand new PTO and kit for an early 4500 that I never used. Current orientation is Left side rear facing. I was going to install the 4500 in my tow truck replacing the 465, but I ended up selling the truck before install.

If it was a late 4500, I'd be quite interested in that. Where do you go to buy a new pto kit?

kwmech 06-30-2021 11:25 AM

Re: PTO swap question
 
I got mine from 6 states


http://www.sixstates.com/products/ca...p?category=PTO

Jmoney01 06-30-2021 02:15 PM

Re: PTO swap question
 
I bought one from a local truck supply house


All times are GMT -4. The time now is 09:41 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com