The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board > Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-15-2024, 04:15 PM   #126
8man
Senior Member
 
Join Date: Sep 2017
Location: Bryan, Texas
Posts: 2,316
Re: Ol' Blue

Well, new endeavor for me today. I got a HF paint gun and some Master Coat rustproofing and for the first time in my life, I mixed paint and sprayed it with a gun.

IMG_1831 by Robert Moorman, on Flickr

I used the Master Coat on the Cherokee frame 12 years ago, and it still looks just like it did the day I "brushed" it on. This means there are some brush marks in it, but there is absolutely no rust. So, this time I thought I'd just try spraying it. I think it worked, but the test will be when I do the topcoat to see if it looks good.

A number of the parts are to hold the Cameo bed fiberglass to the steel bed sides. Some is for the frame, like front bumper mounts and some of the rear spring stuff.

Anyway, I can now say "I'll never be a painter!" Painters have a talent I'll never have. Also, I can make a mess so big it takes hours to clean up, but I did like the way the Mastercoat went on.
__________________
8man-aka Robert
1948 on a S10 Frame, small block with a carb
1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD
Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL]
[/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204
8man is offline   Reply With Quote
Old 08-15-2024, 04:46 PM   #127
Tempest67
Registered User
 
Tempest67's Avatar
 
Join Date: Sep 2018
Location: Ontario
Posts: 822
Re: Ol' Blue

way to go.

I painted with a gun for the first time about 20 years ago, and I enjoyed it. So much that I tried to paint a car, and it worked out fine.

Take your time, don't rush the flash time, and smooth even strokes will give you decent results. (you don't have to cover it with the first coat)

Here is my Lemans in Primer, after Base, after Clear, and finished.

From the prices that I hear that people pay for paint (JUST PAINT) I would start a side business if I had the space.

Congrats, the first time is always the most difficult, now you have done that, you will get better each time.
Attached Images
    
Tempest67 is offline   Reply With Quote
Old 08-15-2024, 06:05 PM   #128
8man
Senior Member
 
Join Date: Sep 2017
Location: Bryan, Texas
Posts: 2,316
Re: Ol' Blue

Nice work Tempest!
__________________
8man-aka Robert
1948 on a S10 Frame, small block with a carb
1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD
Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL]
[/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204
8man is offline   Reply With Quote
Old Today, 09:46 AM   #129
8man
Senior Member
 
Join Date: Sep 2017
Location: Bryan, Texas
Posts: 2,316
Re: Ol' Blue

Ok, I bit the bullet and I sprayed the frame.
IMG_1836 by Robert Moorman, on Flickr
I used the MasterCoat system, two coats of their rust proofing and 2 coats of their topcoat. I used it on the Jeep frame, but I brushed it on and threw away the brushes. This time I sprayed it with the HF paint gun. I won't do it again! Clean up was a total PITA! I went through a box of gloves and 3 rolls of paper towels. It took way more time than it should have. Yes, rust is not going to come back. When I did the Jeep, I put some left over on the shredder and there is no rust where I painted it, but it was just too much of a pain.

I will be assembling the frame next.

I got the cab and doors back from Dip and Strip, and they look great. I took some pictures, but between the phone and the computer, they are not showing up so I can post them. I'll get some more to post later today.

I will start welding up the firewall holes, and getting the cab and doors ready for primer, because they are raw steel right now.

Rignt now, I'm taking the original frame and running gear to storage, just in case I ever need it.
__________________
8man-aka Robert
1948 on a S10 Frame, small block with a carb
1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD
Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL]
[/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204
8man is offline   Reply With Quote
Old Today, 05:08 PM   #130
8man
Senior Member
 
Join Date: Sep 2017
Location: Bryan, Texas
Posts: 2,316
Re: Ol' Blue

Here is what the cab and doors look like after doing the "Strip and Dip" process.
IMG_1838 by Robert Moorman, on Flickr
IMG_1837 by Robert Moorman, on Flickr

Almost all the steel looks like this, multiple layers of old paint removed, some bondo on the bottom of a door where it was dented, any surface rust is gone. The floor will need to be wire wheeled or sanded or something as the solution sat on that flat surface and dried. Now it is like a coating. It can be removed, and it is certainly a lot easier to do just that than the whole cab, doors and hinges.

Next is assemble the painted frame.
__________________
8man-aka Robert
1948 on a S10 Frame, small block with a carb
1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD
Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL]
[/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204
8man is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:13 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com