The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-17-2024, 11:10 PM   #1
jollymon02
Junior Member
 
Join Date: Jun 2021
Location: Fort Worth, TX
Posts: 54
TBI motor tuning

Hey all,

I have a TBI motor running a aftermarket EFI and mild cam. I'm working to get the tuning sorted out. I currently have an HEI distributor with vacuum advance, but have the option to change for a billet and let the EFI handle the timing control, which would make it more like an upgrade from the factory air/fuel delivery.

My immediate question is where should I set the base timing, 0 as factory, or more like a typical SBC 8 degrees base?
jollymon02 is offline   Reply With Quote
Old 07-18-2024, 07:49 AM   #2
biketopia
Senior Member
 
Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,084
Re: TBI motor tuning

What EFI controller? The holley setups have you index the distributor a certain way, lock timing out to a certain number in the tune then verify it stays there at idle and revving it up. Once that's done you do all your timing curve adjustments through programing only. If you set it at 8, the EFI program thinks it's base line is "0" and puts in 8 degrees now your at 16 and having tuning issues.
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop.

07 Silverado Classic 2wd

95 Camaro 427SBC/TH350
biketopia is offline   Reply With Quote
Old 07-18-2024, 09:10 AM   #3
jollymon02
Junior Member
 
Join Date: Jun 2021
Location: Fort Worth, TX
Posts: 54
Re: TBI motor tuning

It is Fitech. Same basic principle. I'm asking if there is a known difference in the tbi vs carb motors calling for different timing for an aftermarket efi. Last distributor car I had was a 70s 2L BMW, so the SBC world is not stored in my brain.
jollymon02 is offline   Reply With Quote
Old 07-18-2024, 03:50 PM   #4
GASoline71
"I ain't nobody, dork."
 
GASoline71's Avatar
 
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,947
Re: TBI motor tuning

Quote:
Originally Posted by jollymon02 View Post
It is Fitech. Same basic principle. I'm asking if there is a known difference in the tbi vs carb motors calling for different timing for an aftermarket efi. Last distributor car I had was a 70s 2L BMW, so the SBC world is not stored in my brain.
Depending on the cam it's gonna need some advance. Start out with 12 degrees or so. The adjust from there. After a few test runs (driving it with a load on the engine), see where the sweet spot is. Small Blocks love advance. However, the TBI "swirlport heads" might negate the gains a bit. They were designed with the severely underpowered TBI in mind.

Gary
__________________
'cuz chicks dig scars...

My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread.

The Rebuild of Creeping Death after the wreck

Quote:
Originally Posted by LONGHAIR View Post
I would never rebuild a 305.
Quote:
Originally Posted by prostreetC-10 View Post
I love using vacuum gauges as part of the carb tuning process. I hook the gauge to the inside of my garbage can and leave it there.
Quote:
Originally Posted by Marv D View Post
Remember Murphys 2nd law of mechanical relationships... "OPPOSING COMPONENTS ATTEMPTING TO OCCUPY THE SAME SPACE, AT THE SAME TIME, GENERALLY END UP OCCUPYING ADJOINING SPACE AT THE BOTTOM OF THE OIL PAN"
Quote:
Originally Posted by cableguy0 View Post
Its cheaper to listen to advice given when you ask for help than it is to ignore everyone and wait for carnage.
GASoline71 is offline   Reply With Quote
Old 08-11-2024, 06:19 PM   #5
PbFut
Senior Member
 
Join Date: Feb 2022
Location: Ca
Posts: 580
Re: TBI motor tuning

I beleive FiTech wants a 10 degree locked out setup. No vac advance, no mechanical. The spark control in their program will manage advance. I recall their max electronic advance is 22 degrees making total max 32. If you don't need 32 on top, you might be able to drop initial and let the computer manage srart up to a greater degree. I am unsure if their system adjusts startup advance.
PbFut is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:36 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com