The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-24-2024, 11:06 AM   #1
epfatboy
Registered User
 
Join Date: Mar 2018
Location: Barrington nh
Posts: 108
Need a little help with my K10

Right after I post this I'll be youtubing a few things as well but I wanted to get this out there as its been a while and I know I'm gonna need a little help.

My problem is I have a '86 K10 and I believe I have a ball joint/wheel bearing problem up front. The problem started by me thinking the rotors were warped as the truck started shaking a bit when I applied the brakes. I dug in and found the rotors to be fine and while I was there I replaced the tie rod ends.

Hoping the problem was solved too her out on a test drive and no dice. And in addition after running it at highway speeds the truck started shaking WITH OUT me touching the brakes... And once it started to shake getting it to stop and not shake again required slowing down to like 20-30 MPH and staying there. It does not feel like a speed wobble.

It was like running it at speed for a bit heated up something and caused it to shake.... All I can think of is the wheel bearings are shot heated up and caused the shaking somehow, but I honestly have not had this happen to me before so I thought I'd ask for a little help.

And since I'm gonna potentially do the wheelbearings/ball joints.... Is there anything else I should be doing? I'm already considering changing out the steering box as it looks like it could be original...

Any good youtube sites I should look at as well to help me with this assembly/dis-assembly?
epfatboy is offline   Reply With Quote
Old 08-24-2024, 12:03 PM   #2
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,702
Re: Need a little help with my K10

Could be idler arm.
Or loose wheel bearings.
Or worst case a cracked frame near the steering box.
Or low air pressure on tires.

Jack up the passenger front tire and grip the two sides of the tire and move it in/out. Watch for movement of tie rods and idler arm. Shouldn’t be much.
Grip the tire top and bottom and move it in/out.
Shouldn’t be much movement. If lots of movement then suspect wheel bearings or wrong torque on them.

You can do that on both sides.
Another remote possibility is a bent rim on front or back.

Last edited by geezer#99; 08-24-2024 at 12:26 PM.
geezer#99 is offline   Reply With Quote
Old 08-24-2024, 12:58 PM   #3
Shifty One
Registered User
 
Shifty One's Avatar
 
Join Date: Dec 2014
Location: Tucson, AZ
Posts: 726
Re: Need a little help with my K10

Inspect the tires closely, could be tread separation.
__________________
1987 V20 farm-hand rescue

1998 C2500 lot-rot rescue
Shifty One is offline   Reply With Quote
Old 08-29-2024, 02:48 PM   #4
57taskforce
All about them K’s
 
57taskforce's Avatar
 
Join Date: Jun 2014
Location: Land of Entrapment
Posts: 6,439
Re: Need a little help with my K10

Quote:
Originally Posted by geezer#99 View Post
Could be idler arm.
Or loose wheel bearings.
Or worst case a cracked frame near the steering box.
Or low air pressure on tires.

Jack up the passenger front tire and grip the two sides of the tire and move it in/out. Watch for movement of tie rods and idler arm. Shouldn’t be much.
Grip the tire top and bottom and move it in/out.
Shouldn’t be much movement. If lots of movement then suspect wheel bearings or wrong torque on them.

You can do that on both sides.
Another remote possibility is a bent rim on front or back.
K10 doesn’t have an idler arm. I’d definitely start at the tires and work your way in. How bad is the shake on a scale of 1-10?
__________________
Tyler
'57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888
'72 K20 Cheyenne: 5” lift, 35’s, front dana 60 blah blah blah… http://67-72chevytrucks.com/vboard/s...d.php?t=662879
‘69 K10 SWB: 4” lift 33”s… in a million pieces http://67-72chevytrucks.com/vboard/s...d.php?t=805206
'98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 35x12.5x20’s
57taskforce is offline   Reply With Quote
Old 08-29-2024, 02:56 PM   #5
MJN
Registered User
 
MJN's Avatar
 
Join Date: Feb 2000
Location: Maquoketa, Ia/ Orr, Mn
Posts: 3,044
Re: Need a little help with my K10

Check your body mounts too- chased a similar issue on a friends truck and ultimately turned out to be worn out body mounts.
__________________
'51 South Bend Model "9A"
'56 Chevy 3600 NAPCO
'74 Chevy Cheyenne Super K20-restored on 37's
'72 GMC Sierra Custom K2500- in progress
'08 GMC Envoy Denali
'12 GMC Sierra 2500HD Denali
'17 GMC Yukon XL
VCCA member #58596
http://www.nohrco.com
MJN is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:29 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com