|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
05-30-2017, 09:16 AM
|
#1 |
|
Registered User
Join Date: Apr 2016
Location: Stockholm
Posts: 273
|
Pictures of steering column
Hope it works now
|
|
|
|
05-30-2017, 09:45 AM
|
#2 | |
|
Registered User
Join Date: Apr 2016
Location: Stockholm
Posts: 273
|
Re: Pictures of steering column
Quote:
The pictures show my new column and PS Box. I mount a new rag joint and my old couple on the box. The shaft comes with the column and I let it run trough the old shaft. The spring and washer is from my old steering. I don't know if this is working, but it looks right, or? Should I drill the two holes on the shaft and fastened it? My question is simply: Does this make any sense to you? Need feedback. |
|
|
|
|
|
05-30-2017, 11:36 AM
|
#3 |
|
Registered User
Join Date: Aug 2012
Location: Topeka Kansas
Posts: 2,655
|
Re: Pictures of steering column
That is a collapsible shaft in the case of a collision and it's supposed to look just like that.
|
|
|
|
|
05-30-2017, 12:51 PM
|
#4 |
|
Registered User
Join Date: Feb 2012
Location: turlock
Posts: 2,177
|
Re: Pictures of steering column
Looks fine to me sir!
__________________
 Project NewType 1972 Chevy C/10 Cheyenne Super ( Daily Driven Showtruck ) http://67-72chevytrucks.com/vboard/s...d.php?t=507903Project Great Grandpa's Legacy 1973 Chevy C/10 Cheyenne ( Current daily driver collecting big time parts ) http://67-72chevytrucks.com/vboard/s...89#post7084289 - Dylan (209)-985-7721 |
|
|
|
|
05-30-2017, 01:20 PM
|
#5 | |
|
Registered User
Join Date: Apr 2016
Location: Stockholm
Posts: 273
|
Re: Pictures of steering column
Quote:
How about the 2 holes? Should I drill holes trough the shaft, or? |
|
|
|
|
|
05-30-2017, 01:24 PM
|
#6 | |
|
Registered User
Join Date: Apr 2016
Location: Stockholm
Posts: 273
|
Re: Pictures of steering column
Quote:
|
|
|
|
|
|
05-30-2017, 01:32 PM
|
#7 |
|
Registered User
Join Date: Jul 2016
Location: Elkhart, Indiana
Posts: 292
|
Re: Pictures of steering column
Yes it's drive able. And no, don't drill holes and fasten it. If anything take it back off and put a little bit of grease on that shaft so in case of a collision the shaft collapses instead of staying put and injuring you.
__________________
1967 Chevy C20 to K20 Conversion "Simply Toxic" http://67-72chevytrucks.com/vboard/s...d.php?t=749409 1971 Chevy C20 Custom Camper LS Swap http://67-72chevytrucks.com/vboard/s...d.php?t=763775 |
|
|
|
|
05-30-2017, 02:19 PM
|
#8 | |
|
Registered User
Join Date: Apr 2016
Location: Stockholm
Posts: 273
|
Re: Pictures of steering column
Quote:
intermediate shaft and coupler only will be used on manuel steering, not power steering. Can anyone verify that? |
|
|
|
|
|
05-30-2017, 02:29 PM
|
#9 | |
|
Registered User
Join Date: Apr 2016
Location: Stockholm
Posts: 273
|
Re: Pictures of steering column
Quote:
Should I put it on the end of the shaft instead? Now the shaft is lose inside both the column and the intermediate shaft. |
|
|
|
|
|
05-30-2017, 05:14 PM
|
#10 |
|
Registered User
Join Date: Apr 2008
Location: Md
Posts: 2,485
|
Re: Pictures of steering column
I believe the spring is intended to hold pressure on the bearing cup, bottom of column, spring, washer, clamp.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=635605 |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
