dual snorkel air cleaner how to.

[doubleb's69]

I already now it has been done and there is another thread on the site that shows pics but I thought I would share the pictures and what I used to make it for anyone who wants to do it themselves. A buddy of mine just built a 383 for his 72 C/10 and wants to make it look stockish and wondered if I would build him one so here is how I did it. There are probably a million ways to do it and different tools to use but these are the ones I used to get to my end result.

Parts list: two air cleaners you don't mind cutting up.

Tool list: drill, cut off wheel, 1/8 inch drill bit, 1 & 1/2 inch hole saw, wire wheel, a vise if you have one, mig welder, die grinder with a carbide bit, vise grips, small screw driver or chisel, and a small hammer.

I started by putting the worst of the two air cleaners in a vise. I then put the 1/8th inch drill bit in the drill and slowly drilled out the factory spot welds. There is one on each corner or 4 total.

After drilling I used a small screw driver and a hammer to lightly pry up the air horn from the air cleaner.

I then drilled out the two spot welds that hold the heat valve to the air horn. I also used the screw driver and hammer to help remove this on both air horns. (This is optional but he wanted it to be smooth.) After breaking the valve loose I wiggled it around to unhook the rod from the flap inside of the air horn and removed the valve all together. I then cut off the end of the rod that runs from either side and pulled it through to remove the valve from within.

After all of the the removal of parts on the air horn I mocked up the general location to make sure all was right and it would work.

[doubleb's69]

I then removed the clamped on air horn and I cut off the heat riser tube (optional) on both air horns to allow more air in and cleaned it up with a grinder and file.

I then went to the first air cleaner and cut out the flange so it could be utilized in the second base so that there would not be any gaps and look factory from the outside. I cut it 2 inches on both sides and at the bottom and top as far as I could. I drilled four 1/8th inch holes in the flange for spot welds to secure it the the air cleaner. One in each corner. I then set it aside for later.

I moved on to where I decided I would put the snorkeld on air cleaner #2 and measured it out. I used a 1 and a 1/2 inch hole saw on both ends of the measurement and a cut off wheel to connect the two. I then used to die grinder with the carbide bur to modify the opening to slip the flange from air cleaner #1 into air cleaner #2.

I then slipped the flange in from the inside of the air cleaner. I took the air horn and fitted it over the flange to make sure everything was level and symetrical to the other air horn. After I had it where I wanted it I used vise grips to secure it while I spot welded it.

[doubleb's69]

I then refitted the air horn over the flange and spot welded it as well. I used the die grinder and carbide bur to smooth out the welds since they where in a tight area.

This is how I did mine and like I said there are probably easier ways out there but if you have a few hours to kill and have the parts it is very easy.

I will be welding up all of the holes and then sand blasting it. After that I will put some putty on the air horns and smoothing them out. I will follow it up with some semi gloss black on then it will go to its new home.

[black_sheep454]

Looks good
Posted via Mobile Device

[shawno72]

I like it

[Dieselwrencher]

Nice work Bud!

[doubleb's69]

Thanks fellas. I will be putting a later model lid on it so that we can fit a 4 inch filter under in it.

Here is the engine it will be going on.

383 with flat tops, Dart heads, Edelbrock Performer RPM, and Comp Cams 292 magnum .501/.501 with 244 degrees at .050 and 110 lobe seperation. It oughta run and sound pretty good.

[big_al_71]

Man I love when someone builds something rather than buying it..Great write up.

[GRX]

Originally Posted by big_al_71

Man I love when someone builds something rather than buying it..Great write up.

x2,127,489

[robzilla]

going to have to make one too, got to find another air cleaner, as i got rid of the extra one i had....

[bobs409]

Been planning one of these for a while now. I just have to cross off the 994 things on the list before it!

[RANDY COX]

Kool good job,I made me one of those a few yrs back for my Blazer..there's nothing like OEM...extra parts laying around...

[doubleb's69]

Thanks guys. I made this one for a friend using my last two air cleaners I had. Now that I see the results I need to find two more to build one for myself . I will post pictures after it is finished and painted and in the truck.

[doubleb's69]

Here are a couple updated pics. Still trying to locate a 88-92 single stud TBI air cleaner lid so we can run a 4" filter.

[shawno72]

Looking real good.

[yuccales]

That looks real nice!

[oldblue1968chevy]

Sweet man, good job

[special-K]

That came out nice! I made one using later snorkels that are shorter and bigger

[doubleb's69]

I think I finally located a lid. I will blast it and paint it as soon as I get it.

[weever82]

Awesome job! You are a good buddy to be doing that for him!
Posted via Mobile Device

[GTJ558]

i have a tbi chrome air lid with script edelbrock never been used...its basically been wall art since i bought it many years ago when i had my blazer.

[doubleb's69]

I just got a lid today. It is off of a 72 Monte Carlo so it isn't as tall but I can still fit a 3" filter under it. I wanted a TBI lid because they have a 4" filter.

[GTJ558]

no problem i figured id chime in maybe give a little help. glad you got a lid.

[54blackhornet]

Question ? Would 2nd horn increase heat to carb if you had both connected to the vacume controller ? Like two heat risers off both manifolds open to warm up then close off when warm . IT IS COLD IN OREGON !
Posted via Mobile Device

[rambler]

nice write up.. I want to to do this someday,, just got to get the truck running again