WA 4wd trans crossmember, semi gloss powder coat, $150 shipped

[randy500]

Very clean piece...

[randy500]

Underside

[randy500]

Ttt

[StruttinSoul]

Do you still have these crossmembers? I'm actually in need of two so I can use the skid plate - I've already got the arms that go to the top of the frame so don't necessarily need those

[randy500]

Originally Posted by StruttinSoul

Do you still have these crossmembers? I'm actually in need of two so I can use the skid plate - I've already got the arms that go to the top of the frame so don't necessarily need those

I do still have this one. I will look for a bottom one and post back. Where you also looking for the strut arm from the transfer case to the bell housing? I have a small stock of those too.

[StruttinSoul]

Originally Posted by randy500

I do still have this one. I will look for a bottom one and post back. Where you also looking for the strut arm from the transfer case to the bell housing? I have a small stock of those too.

Thanks! Yeah I was also looking for one of those

[randy500]

I have the lower crossmember in the picture below the powder coated one. I can do $200 shipped for both to a US address.

[StruttinSoul]

Originally Posted by randy500

I have the lower crossmember in the picture below the powder coated one. I can do $200 shipped for both to a US address.

Sounds good, I'll take them - I'll put my US post box in the comments of the payment.

[StruttinSoul]

Originally Posted by randy500

I have the lower crossmember in the picture below the powder coated one. I can do $200 shipped for both to a US address.

Payment sent

[randy500]

Originally Posted by StruttinSoul

Payment sent

I see the payment and address, I will ship that by tomorrow morning and send you tracking info. Thanks.

[StruttinSoul]

Awesome thanks Randy!

[randy500]

Originally Posted by StruttinSoul

Awesome thanks Randy!

Your welcome, shipped and tracking posted in paypal, dropping off at ups store in a bit.

[Killer Bee]

Originally Posted by randy500

I do still have this one. I will look for a bottom one and post back. Where you also looking for the strut arm from the transfer case to the bell housing? I have a small stock of those too.

any of these struts available? with hardware? do you know if there is an exhaust routing issue, possibly with headers? shipping to 90744 please, thank you!

side question if you can answer; what's the story on the cross member hole pattern? the two top and bottom in the picture above are drilled both sides for what appears to be the skid plate pattern and one mount hole is elongated.. the black one in the middle does not have the extra holes. were the OE skid plate optioned cross members drilled this way at the factory? done by dealer? thank you!

I bought a bare skid plate from Koop and couldn't find cross member.. two weeks later got a good deal on a powder coated cross member and skid plate.. none of the cross members in my K20 or K1500 are drilled, or have struts in them for that matter.. so trying to figure out what to do with the extra plate, maybe add it to the other side just to protect the cross member and minimize the exposed edge when wheelin'.. I split a lighter duty trans cross member in two on rock in mojave a few years back and the manual trans wouldn't reach any gears in the rear of the pattern because the shifter was hitting the floor opening

[randy500]

Originally Posted by Killer Bee

any of these struts available? with hardware? do you know if there is an exhaust routing issue, possibly with headers? shipping to 90744 please, thank you!

side question if you can answer; what's the story on the cross member hole pattern? the two top and bottom in the picture above are drilled both sides for what appears to be the skid plate pattern and one mount hole is elongated.. the black one in the middle does not have the extra holes. were the OE skid plate optioned cross members drilled this way at the factory? done by dealer? thank you!

I bought a bare skid plate from Koop and couldn't find cross member.. two weeks later got a good deal on a powder coated cross member and skid plate.. none of the cross members in my K20 or K1500 are drilled, or have struts in them for that matter.. so trying to figure out what to do with the extra plate, maybe add it to the other side just to protect the cross member and minimize the exposed edge when wheelin'.. I split a lighter duty trans cross member in two on rock in mojave a few years back and the manual trans wouldn't reach any gears in the rear of the pattern because the shifter was hitting the floor opening

I still have some of those struts, those came from square body trucks, not sure of the trans and transfer case setups, they will either fit or need cutting and welding for length.

As for the crossmember center hold pattern...I think the elongated center hole with the heat shield is square body too.
I'm not sure about the drilling for skid plates, I have noticed all the ones I have are drilled...

I will post a pic of the strut rods later, I saw them a few weeks ago when I was cleaning...

[Killer Bee]

thank you! I'm handy with a welder and cutting tools so I may give it a shot in my '71.. I plan to off road a little bit so any extra strength in the drivetrain is welcome..

the hole pattern would be handy predrilled but I can lay it out with a skid plate for a template..

curious though about the one you pictured in powder coat missing some of the holes the top and bottom ones have.. was making me wonder if I should keep shopping for two of those instead of drilling mine..

I already have a few locations I plan to heat shield because of headers and high n tight exhaust route.. I like the way exhaust is routed but rather have a couple of components shielded from the heat..

thanks again and no rush on my account, progress is slooow on this end..

[randy500]

Pics of the transfer case strut rods, bellhousing to first bolt hole center is about 32”

[Killer Bee]

what are you asking for one of those struts? shipping to 90744?

I might just give it a shot in my '71 and report results..

btw, could you post the measurements of the hole pattern on the bottom of a cross member with extra holes for skid plate?

thank you!

[Killer Bee]

struts for sale?

Originally Posted by Killer Bee

what are you asking for one of those struts? shipping to 90744?

I might just give it a shot in my '71 and report results..

btw, could you post the measurements of the hole pattern on the bottom of a cross member with extra holes for skid plate?

thank you!

[randy500]

Originally Posted by Killer Bee

struts for sale?

Yes, $75 shipped each, I’m guessing shipping is about $30...

[Killer Bee]

$105 a quote to commercial address 90744?

if so I'll send now, thank you.

[randy500]

Just send the $75, i was just explaining my cost of shipping.

[Killer Bee]

sorry, was getting ready for work and missed the 'shipped' part..

please don't cut yerself short, if you need an adjustment, no argument here..

I almost never ship anything so I have no idea..

$75 sent to your paypal to get us rolling, again, if shipping is excessive please tell me..

and no rush, just wanted to close a deal so at least one has my name on it, thank you!

[randy500]

Originally Posted by Killer Bee

sorry, was getting ready for work and missed the 'shipped' part..

please don't cut yerself short, if you need an adjustment, no argument here..

I almost never ship anything so I have no idea..

$75 sent to your paypal to get us rolling, again, if shipping is excessive please tell me..

and no rush, just wanted to close a deal so at least one has my name on it, thank you!

Its all good, money received, sending you your UPS tracking number now.

[Killer Bee]

strut received, thank you!

[randy500]

Originally Posted by Killer Bee

strut received, thank you!

Your welcome.