FL Moser Ford 9" axle housing w/31 spline axles

[Chevy072]

This kit was installed around a year ago and just sat not being used. Retail is over $1000. This bolts right into your 67-72 truck with trailing arms. All you need to do is pick up a 9" center chunk with your choice of gears, etc. NEW PRICE $350 picked up.

I also have the leafspring mounts for this that need to be welded in place. I will check to make sure they are the right ones because they were just sitting in the cab.

I want to clarify that this is not a Ford rearend,but is produced by moser engineering. They have modeled this housing after the Ford 9". The wheel studs are 4 on 4.75

[lucifer]

Originally Posted by Chevy072

This kit was installed around a year ago and just sat not being used. Retail is over $1000. This bolts right into your 67-72 truck with trailing arms. All you need to do is pick up a 9" center chunk with your choice of gears, etc. $500 o.b.o picked up.

Does it maintain the stock width??

[Chevy072]

Originally Posted by lucifer

Does it maintain the stock width??

housing itself is approx. 60-1/2" and outer axle to outer axle is approx 66-1/2

[Chevy072]

anyone interested? I do have the drum brakes for this,but they have been sitting for a while and will need to be cleaned up.

[Chevy072]

offer?

[Chevy072]

Offer?

[Chevy072]

New price $400

[PRORIDES]

Would you ship it to PA? Thanks

[Chevy072]

Originally Posted by PRORIDES

Would you ship it to PA? Thanks

Sure would. I will let you know tomorrow on what it would cost to get it there.

[Chevy072]

Originally Posted by PRORIDES

Would you ship it to PA? Thanks

Not sure of your zip code,but Fedex to 15219 would be around $130 for shipping. That is with me just wrapping it. If it was crated it would be more. I can get a crated quote on monday through engines direct

[chevytruckluver]

bump for a great deal, wish I could use it

[Chevy072]

good morning

[Chevy072]

no interest?

[Chevy072]

Anyone? This is around 1/3 of the retail price.

[Chevy072]

ttt

[Chevy072]

anyone?

[Chevy072]

bump

[Chevy072]

ttt

[Chevy072]

bump

[Chevy072]

ttt

[Chevy072]

Anyone interested?

[Chevy072]

ttt

[duallyjams]

Originally Posted by Chevy072

This kit was installed around a year ago and just sat not being used. Retail is over $1000. This bolts right into your 67-72 truck with trailing arms. All you need to do is pick up a 9" center chunk with your choice of gears, etc. NEW PRICE $400 picked up.

I also have the leafspring mounts for this that need to be welded in place. I will check to make sure they are the right ones because they were just sitting in the cab.

I want to clarify that this is not a Ford rearend,but is produced by moser engineering. They have modeled this housing after the Ford 9". The wheel studs are 4 on 4.75

Do you still have the build sheet for this to show what bearing , wheel stud that you chose also this package on moser site comes with brakes and the moser site shows 63-69 and the 70-72 as different width.

[Chevy072]

Originally Posted by duallyjams

Do you still have the build sheet for this to show what bearing , wheel stud that you chose also this package on moser site comes with brakes and the moser site shows 63-69 and the 70-72 as different width.

No i don't have the build sheet. I did not purchase this directly. The wheel studs are 7/16 by 1-1/4". The do not come standard with brakes,but can be ordered that way. I do have drum brakes for it that have been sitting out and will need some freshening up. The wheel studs are 4 on 4.75 which i thought was strange that this was ordered like that,but then i checked the front disk setup with tubular control arms and it was also 4 on 4.75,so im guessing that this was ordered that way for a reason. The bearings would be moser or timkin ball bearing type according to moser tech support. They do not use cheap bearings. It also has the c-clip eliminator type on it. The housing itself is 60.5" long and outside to outside on the axles without counting the studs is 65.5"

[Chevy072]

ttt