NY Factory Jack Setup

[lane224]

Factory Jack Setup.
$150 + Ship

[tristan]

I will take it, PM sent.

[Farrgor]

Good find Tristan. Put me in line Lane if you run across another good set.

[lane224]

Originally Posted by tristan

I will take it, PM sent.

Pm'd you

[mdunn]

Put me in line also! Wish I would have seen this one.

[tristan]

Payment sent, thanks.

[preciador6]

Does anyone have a picture of this set up on the blazer were all this goes originally ,Thanks.

[craneboy72]

Like this?

[preciador6]

ok thanks guys.

[1rippen6]

I have a setup but the lug wrench is 3/4 but pretty sure its not correct 125 plus shipping.

[Cheyennekid]

Do u still have the jack setup 1rippen6 if so pm me

[1rippen6]

Originally Posted by Cheyennekid

Do u still have the jack setup 1rippen6 if so pm me

PM sent

[NorthernMatthew]

Do you still have a jack by itself?

[1rippen6]

Originally Posted by NorthernMatthew

Do you still have a jack by itself?

I may have another jack will have to look but let lane224 response first.

[lane224]

Originally Posted by 1rippen6

I may have another jack will have to look but let lane224 response first.

Only jacks I have right now are out of 73-75. Hopefully Dwayne has one hidden somewhere.

[1rippen6]

I will look tomorrow for a jack

[1rippen6]

Originally Posted by NorthernMatthew

Do you still have a jack by itself?

I found another one was rusty so I blasted it. It does have some pitting on the one side and bottom but shouldn't affect it. Its the one with the etching primer. 40 plus shipping should fit in a medium flat rate for 13.

[NorthernMatthew]

Thanks a lot -- so that's the correct jack for a 72 Blazer and it works properly?

[1rippen6]

Originally Posted by NorthernMatthew

Thanks a lot -- so that's the correct jack for a 72 Blazer and it works properly?

Yes should be correct as far as working properly it goes up and down fine. I can throw it under the K5 I have setting in the yard and check it out if you like.

[NorthernMatthew]

Originally Posted by 1rippen6

Yes should be correct as far as working properly it goes up and down fine. I can throw it under the K5 I have setting in the yard and check it out if you like.

Thank you - I tried to reply earlier but didn't do it right. I'm looking for the correct 72 Blazer Jack so if you need to try it under yours to confirm, I'd really appreciate that. You don't have any proper levers I don't suppose hey?
Posted via Mobile Device

[1rippen6]

Actually looking for other parts in the last couple of days I found a handle and another lug wrench. I will post a picture later this evening I have plans right after work. It will be a setup as pictured above 150 plus shipping for everything. I don't think I want to separate at this time, I will give you first shoot and then mdunn next.

[NorthernMatthew]

Originally Posted by 1rippen6

Actually looking for other parts in the last couple of days I found a handle and another lug wrench. I will post a picture later this evening I have plans right after work. It will be a setup as pictured above 150 plus shipping for everything. I don't think I want to separate at this time, I will give you first shoot and then mdunn next.

Posted via Mobile Device

[NorthernMatthew]

Originally Posted by 1rippen6

Actually looking for other parts in the last couple of days I found a handle and another lug wrench. I will post a picture later this evening I have plans right after work. It will be a setup as pictured above 150 plus shipping for everything. I don't think I want to separate at this time, I will give you first shoot and then mdunn next.

I think I have the correct handle, can you do me a favor and measure the two lengths please?
Posted via Mobile Device

[1rippen6]

Here is the stuff I found lug wrench long side about 15 3/4 short side 4 5/8

[chevycc1970]

Originally Posted by 1rippen6

Here is the stuff I found lug wrench long side about 15 3/4 short side 4 5/8

I'll get in line as well.