![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Next project: 1970 K10
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
|
WTB: P/S pump pulley, GM #3993325DJ
Needed: Power steering pump pulley.
This one has part number 3993325DJ stamped on it. I think it came off of a 72 4x4 small block, no A/C. This one is bent to sh!t. Kinda scared to call the dealer, but I suppose I will have to if I can't find a good used one. Thanks!!!
__________________
Bob 1970 Chevy K10 LWB "Goldie" 350/TH350 next project!! 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jul 2001
Location: Neenah, WI
Posts: 327
|
With the cost of the new pulley compared to the hassle of removing a PS pulley from a used pump I'd say go to the dealer. At least that is wht I did. Sometimes those pulleys are on there darn hard and unless you have the right puller it will be difficult to get off. I don't remember wha I paid, but maybe $20 or so.
Rak |
![]() |
![]() |
![]() |
#3 |
Next project: 1970 K10
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
|
I have a puller, it came off real easy.
__________________
Bob 1970 Chevy K10 LWB "Goldie" 350/TH350 next project!! 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jul 2001
Location: Neenah, WI
Posts: 327
|
Ahh, maybe its just me! I never had an actual ps pulley puller, just a generic snap on puller set and for the life of me I couldn't get the last one off I tried.
|
![]() |
![]() |
![]() |
#5 |
Keepin an eye out
Join Date: Feb 2003
Location: So.Cal
Posts: 3,921
|
Power steering pulleys bend easy, I would go new. Theres lots on Ebay.
__________________
1970 Chevy C10 SWB 5.3 1996 Toyota Tacoma SR5 4x4 2007 Vespa GTS 250 Scooter ZIP 91351 |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Nov 2001
Location: Fletcher,N.C U.S.A
Posts: 162
|
I called the dealer and they said they were discontinued.
|
![]() |
![]() |
![]() |
#7 |
Next project: 1970 K10
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
|
Yup, not available from the dealer.
Those that are on eBay, how many different variaties are there of the keyway'd pulleys? Other than different diameters (if that is the case), is there different backspacing (?)
__________________
Bob 1970 Chevy K10 LWB "Goldie" 350/TH350 next project!! 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE |
![]() |
![]() |
![]() |
#8 |
Keepin an eye out
Join Date: Feb 2003
Location: So.Cal
Posts: 3,921
|
Keyed are keyed through '84 and all the small block ones are pretty much the same. I would go w/ a aluminum one as the steel ones(on Ebay) are cheap China jobs and tweak easy. You may also find a OE one on Ebay.
__________________
1970 Chevy C10 SWB 5.3 1996 Toyota Tacoma SR5 4x4 2007 Vespa GTS 250 Scooter ZIP 91351 |
![]() |
![]() |
![]() |
#9 |
Next project: 1970 K10
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
|
Thanks, boraxman. I checked eBay and found an aluminum one. Good deal, since I have aluminum pulleys already.
And you are absolutely correct about the chrome ones. I bought a chrome water pump pulley. Bent hunk of junk!! That's why I went with aluminum
__________________
Bob 1970 Chevy K10 LWB "Goldie" 350/TH350 next project!! 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Nov 2003
Location: Monroe, La 71202
Posts: 317
|
i have one off a 72 k20 4x4. pulled it off this weekend. it wasnt bent that i know off but ill double check just to make sure if your intrested.
69k5 |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Nov 2003
Location: Monroe, La 71202
Posts: 317
|
ill double check that part # as well.
|
![]() |
![]() |
![]() |
#12 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Seems like about 1/2 of them are bent nowdays.
I just tweak them back till they are running true again. I've done this to several and never had any more trouble out of them.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#13 |
"Trucks with Class"
![]() Join Date: Jul 2000
Location: OLYMPIA, WA, USA
Posts: 8,132
|
Like TX FIREFIGHTER said, use a rubber hammer to tap the high spot and they normally straighten right up. They bend easy and they straighten easy.
|
![]() |
![]() |
![]() |
#14 |
Next project: 1970 K10
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
|
I went ahead and bought an aluminum one off of eBay. But I might go ahead an try to straighten this one out just to have around for the next project
![]()
__________________
Bob 1970 Chevy K10 LWB "Goldie" 350/TH350 next project!! 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE |
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Nov 2003
Location: Monroe, La 71202
Posts: 317
|
itwas the right one if you decide you want it later.
69k5 |
![]() |
![]() |
![]() |
#16 |
Next project: 1970 K10
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
|
Thanks 69k5. I'll keep it in mind for the next project. How much do you want for it? Send me a PM if you want.
Thanks, Bob
__________________
Bob 1970 Chevy K10 LWB "Goldie" 350/TH350 next project!! 1981 Chevy C10 LWB 355/TH350 - My son's truck LS SWAP FORUM! Tons of LS swap info here! PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET! CLICK HERE FOR THE FAQ INDEX by KRUE |
![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: Nov 2003
Location: Monroe, La 71202
Posts: 317
|
pm sent
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|