![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Nov 2001
Location: SoCal
Posts: 136
|
![]()
I see there are two idle adjusters...one the idle stop (throttle arm) and the other the idle needles. How do you go about adjusting the idle? Do you start with the idle needles? What's the best method?
Thanks, Ken [This message has been edited by Cal69Chevy (edited April 03, 2002).]
__________________
'69 Chevy, 4X4-SB 350 TBI-TH350 Trans-205 Transfer Case-Dana 44 Front-14 Bolt Rear-Front Disc Brakes-Factory A/C-P/S Ken's '69 Page |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jan 2001
Location: Killingworth, CT. USA
Posts: 3,378
|
![]()
If tools and equipment are not avalible what I would do is warm engine up to operating temp, set parking brake, block wheels, drop transmission into drive,(assuming it's automatic) now we are also assuming the carb is healthy, turn one side in until the engine rpms start to drop, now back off screw 1/4- 1/2, now do the same for the other, now return to first one and do that one over again, adjust engine idle screw to specs, this should put you in the ball park.
------------------ 1971 C10 swb stepside 350/700R4/3.73posi Killingworth, Connecticut
__________________
1971 C10 swb stepside 350/700R4/3.73posi (retired as of 4/22/03) 1998 S10 short bed 2002 S10 Blazer 1942 Oldsmobile 1958 Massey Harris Pony 1951 Wife Killingworth, Connecticut May those who love us, love us, any of those who do not love us, may God turn their hearts. And if God is unable to turn their hearts, may he turn their ankles so we may know them by their limping. A man who works with his hands is a laborer; a man who works with his hands and his brain is a craftsman; but a man who works with his hands and his brain and his heart is an artist. |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2001
Location: SoCal
Posts: 136
|
![]()
i must be dense...or it's late after a long day..but what do you mean set the engine idle screw to spec? what is the spec?
__________________
'69 Chevy, 4X4-SB 350 TBI-TH350 Trans-205 Transfer Case-Dana 44 Front-14 Bolt Rear-Front Disc Brakes-Factory A/C-P/S Ken's '69 Page |
![]() |
![]() |
![]() |
#4 |
Recovering Truck Driver
Join Date: Mar 2002
Location: Orleans, NE USA
Posts: 1,883
|
![]()
on a stock 350, i believe spec is 550 rpm at idle in drive. I'm not positive on this as it's been awhile since I looked in the book and it's in the barn. Mine idles at 750 in park and about 580 in drive.
------------------ '72 Chevy 1/2T 4x4 shortbox stepside 350/350auto on '84 ralleys and 31/10.5s 67 Cutlass convertible 330, 3spd stick 90 GMC Jimmy 350/auto Chad Stephens Orleans,NE
__________________
67 K-20 350, SM465, Eaton rear, 4.56 no spin option 00 Dodge 2500 4x4, 24V cummins, 5 speed Chad South Central Nebraska |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2001
Location: Killingworth, CT. USA
Posts: 3,378
|
![]()
Yeah,,,550 to 600 should be fine in drive or 700 to 750 in neutral, any more than that and you may experience dieseling or run on when you shut down.
------------------ 1971 C10 swb stepside 350/700R4/3.73posi Killingworth, Connecticut
__________________
1971 C10 swb stepside 350/700R4/3.73posi (retired as of 4/22/03) 1998 S10 short bed 2002 S10 Blazer 1942 Oldsmobile 1958 Massey Harris Pony 1951 Wife Killingworth, Connecticut May those who love us, love us, any of those who do not love us, may God turn their hearts. And if God is unable to turn their hearts, may he turn their ankles so we may know them by their limping. A man who works with his hands is a laborer; a man who works with his hands and his brain is a craftsman; but a man who works with his hands and his brain and his heart is an artist. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|