rear disc brake rotors - The 1947 - Present Chevrolet & GMC Truck Message Board Network

sinister72 · 10-03-2004, 12:39 PM

Looking for a source for rotors for my rear disc set up. I have the brackets and caliplers,now just need the rotors.

MOTHERTRUCKERS · 10-03-2004, 10:19 PM

Rotors off of what vehicle? what calipers and brackets do you have?

sinister72 · 10-03-2004, 10:44 PM

Hey Mother
Changing The Drums Off My 72 Swb,have Set Of Cailipers Off El-dorado,,,

dmec · 10-04-2004, 12:46 AM

for rotors use 77-79 cad seville or 95 & up caprice. seville rotors require turning down axle flange so rotor will fit over it. caprice bolt holes need to be enlarged slightly but will fit over stock flange. caprice rotor thinner than cad and will probably need to fab a set of shims for pads. these are 11 inch rotors. make sure your brackets are for the large rotors. some brackets are for 10 1/2 inch rotors.

MOTHERTRUCKERS · 10-04-2004, 06:36 AM

Barely used lots of miles left 77-9 seville rotors 60.00 + shipping I can mic them for you today if needed. i also have new in my loft somewhere and 7 complete setups with e-brakes 4 still on the housings.

MOTHERTRUCKERS · 10-05-2004, 09:02 PM

ttt

10-03-2004, 12:39 PM	#1
sinister72 Registered User Join Date: Apr 2002 Location: Bowling Green, kentucky Posts: 182	rear disc brake rotors Looking for a source for rotors for my rear disc set up. I have the brackets and caliplers,now just need the rotors. __________________ 72 chevy C-10 swb fleetside,402 BB.700r4,buckets,console.etc. 72 Blazer CST 350,AT, new project 1971 Chevy Nova ,355 SB blow through turbo in works.

10-03-2004, 10:19 PM	#2
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	Rotors off of what vehicle? what calipers and brackets do you have? __________________ Rest in Peace Ed. Thanks for all the good times.

10-03-2004, 10:44 PM	#3
sinister72 Registered User Join Date: Apr 2002 Location: Bowling Green, kentucky Posts: 182	Hey Mother Changing The Drums Off My 72 Swb,have Set Of Cailipers Off El-dorado,,, __________________ 72 chevy C-10 swb fleetside,402 BB.700r4,buckets,console.etc. 72 Blazer CST 350,AT, new project 1971 Chevy Nova ,355 SB blow through turbo in works.

10-04-2004, 06:36 AM	#5
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	Barely used lots of miles left 77-9 seville rotors 60.00 + shipping I can mic them for you today if needed. i also have new in my loft somewhere and 7 complete setups with e-brakes 4 still on the housings. __________________ Rest in Peace Ed. Thanks for all the good times.

10-05-2004, 09:02 PM	#6
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	ttt __________________ Rest in Peace Ed. Thanks for all the good times.

10-04-2004, 12:46 AM	#4
dmec Senior Member Join Date: Jun 2000 Location: yucaipa ca Posts: 580	for rotors use 77-79 cad seville or 95 & up caprice. seville rotors require turning down axle flange so rotor will fit over it. caprice bolt holes need to be enlarged slightly but will fit over stock flange. caprice rotor thinner than cad and will probably need to fab a set of shims for pads. these are 11 inch rotors. make sure your brackets are for the large rotors. some brackets are for 10 1/2 inch rotors.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.