Replacing 69 bed floor w/ 90 bed floor..need measurements. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Bleach · 10-28-2004, 07:45 PM

I have a line on a SWB 1990 bed that a guy will sell me for 200 bucks. I only want it for the sheetmetal in the floor to use in my 69. I know that the older trucks have a narrower bed. So...I need the following.

I need to know if the 1990 has enough bed sheetmetal to cover everything, wheel wells are my concern.

I also need to get some kind sole to give me some measurments, advice, pics..etc. What I really need are the measurements of the true dimensions of a 69-72 SWB fleet bed floor.

This won't happen for a while, but if this will work I need to go ahead and pick up this bed while I can.

Thanks in advance!

Longhorn Man · 10-28-2004, 08:41 PM

step side, or fleet?

GMC71k20 · 10-28-2004, 08:59 PM

you might as well just spend the money on the material to put a wood bed with stainless steel strips in your bed.

68C15 · 10-29-2004, 07:07 AM

I'm not sure if the '90 is the same as a '98 but my boss gave me a bed mat from his '98. it comes about 4 inches narrow on each side. I suggest finding one from a '73-'87 instead. you may have to do some patching for where the filler neck bulge is on the floor.

Bleach · 10-29-2004, 07:29 AM

Woops, left out important info there.......the 69 is a fleet and the 90 is a fleet. I can't find the older model beds....which ones are a direct fit?

Bleach · 10-29-2004, 07:30 AM

P.S., I don't want a wood bed.

crazy longhorn · 10-29-2004, 07:01 PM

I built a steel floor for my longhorn, & while it was a little work, The cost in materials wasnt bad. the crossrails are 2x3x1/8 wall rect tubing, with a 3x3 on the rear. i have a few rooftop shots of the bracework..... http://community.webshots.com/user/hotrodhorn i think you will find it easier to build from "scratch", than try to fit a later floor to your box. best of luck,crazyL

Bleach · 10-29-2004, 10:09 PM

Hey crazy, what was your cost in materials.......explain your bed support rails again, I didn't catch it.

Thanks!

crazy longhorn · 10-31-2004, 11:35 AM

Cost of materials? Its been a while, but to my best guess around $175. I basically replaced the stock crossbeams for the box with square , & rectangular tubing. the floor can then be layed in treadplate, & painted or spray lined. its not a pretty as a wood floor, but very strong. best of luck,crazyL

10-28-2004, 07:45 PM	#1
Bleach this guy Join Date: Apr 2004 Location: Southwest VA Posts: 122	Replacing 69 bed floor w/ 90 bed floor..need measurements. I have a line on a SWB 1990 bed that a guy will sell me for 200 bucks. I only want it for the sheetmetal in the floor to use in my 69. I know that the older trucks have a narrower bed. So...I need the following. I need to know if the 1990 has enough bed sheetmetal to cover everything, wheel wells are my concern. I also need to get some kind sole to give me some measurments, advice, pics..etc. What I really need are the measurements of the true dimensions of a 69-72 SWB fleet bed floor. This won't happen for a while, but if this will work I need to go ahead and pick up this bed while I can. Thanks in advance! __________________ Duct tape is like The Force. It has a light side, a dark side, and it holds the universe together.

10-29-2004, 07:07 AM	#4
68C15 blood type; Retumbo Join Date: Jan 2004 Location: next to my reloading bench Posts: 10,269	I'm not sure if the '90 is the same as a '98 but my boss gave me a bed mat from his '98. it comes about 4 inches narrow on each side. I suggest finding one from a '73-'87 instead. you may have to do some patching for where the filler neck bulge is on the floor. __________________ Man rule #77...if you own a 67 stepside with a caddy 472 you will never be in danger of loosing you man card

10-29-2004, 07:29 AM	#5
Bleach this guy Join Date: Apr 2004 Location: Southwest VA Posts: 122	Woops, left out important info there.......the 69 is a fleet and the 90 is a fleet. I can't find the older model beds....which ones are a direct fit? __________________ Duct tape is like The Force. It has a light side, a dark side, and it holds the universe together.

10-29-2004, 07:30 AM	#6
Bleach this guy Join Date: Apr 2004 Location: Southwest VA Posts: 122	P.S., I don't want a wood bed. __________________ Duct tape is like The Force. It has a light side, a dark side, and it holds the universe together.

10-29-2004, 07:01 PM	#7
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	I built a steel floor for my longhorn, & while it was a little work, The cost in materials wasnt bad. the crossrails are 2x3x1/8 wall rect tubing, with a 3x3 on the rear. i have a few rooftop shots of the bracework..... http://community.webshots.com/user/hotrodhorn i think you will find it easier to build from "scratch", than try to fit a later floor to your box. best of luck,crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

10-28-2004, 08:41 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	step side, or fleet?

10-28-2004, 08:59 PM	#3
GMC71k20 Registered User Join Date: Aug 2002 Location: mass Posts: 1,277	you might as well just spend the money on the material to put a wood bed with stainless steel strips in your bed.

10-29-2004, 10:09 PM	#8
Bleach this guy Join Date: Apr 2004 Location: Southwest VA Posts: 122	Hey crazy, what was your cost in materials.......explain your bed support rails again, I didn't catch it. Thanks! __________________ Duct tape is like The Force. It has a light side, a dark side, and it holds the universe together.

10-31-2004, 11:35 AM	#9
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	Cost of materials? Its been a while, but to my best guess around $175. I basically replaced the stock crossbeams for the box with square , & rectangular tubing. the floor can then be layed in treadplate, & painted or spray lined. its not a pretty as a wood floor, but very strong. best of luck,crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.