![]() |
|
![]() |
#1 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
wtf mate?
i went out and tried to put my driveshaft in tonight and it will only go part way in. it goes probably almost exactly halfway and stops? wth?
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: Mar 2004
Location: Somewhere
Posts: 985
|
do you have a long or short yoke on the driveshaft? are there any burrs/ rust inside the yoke?
ondrew |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
i dont know length wise...it was a 3 speed manual truck before. i was told it will be a direct fit to the TH350. i cleaned it out with a little wire brush before installing. i was told there is a bushing in the tail shaft and i might have to sand the driveshaft yoke a little? is that true?
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Feb 2003
Location: Mesquite, Tx
Posts: 396
|
Make sure the splines are not twisted on the output shaft of the tranny or the yoke. The slip yoke should be able to go all the way into the tranny.
__________________
GM 330HP/350, Magnuson 122HH, Tremec TKO 5spd |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
it goes really easy almost exactly half way...then stops. if they were twisted it would twist at the end right?
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#6 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Stick it in there till it bottoms and mark it with a Sharpie, then remove it and stick your finger into the yoke and see if it's bottomed out at that depth.
If there is any rust on the yoke, you may as well remove the tailhousing and change the seal now before you puke fluid onto the ground. Trying to put in the rusty yoke will have damaged the seal. Yokes are to be polished smooth and rust free with emery cloth or crocus cloth.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
i took pics...yellow is where it goes...red is where it should go it looks like.
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
more
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
they look straight to me...
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#10 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
Something is wrong. It should go on to the red line. The yoke looks good in the pics.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
hence why i am puzzled....is that bushing thing true? should i sand it like i was told?
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#12 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
If it's a used bushing, it should definitely be loose enough to work. I've never had to do anything to the bushing to make the yoke fit, ever.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Mar 2004
Location: Butler PA
Posts: 3,034
|
they said sand the yoke a little.
__________________
67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt. |
![]() |
![]() |
![]() |
#14 |
Senior Member
![]() Join Date: Feb 2003
Location: WIS
Posts: 1,752
|
burr
There must be a burr on one of the splines. If you still have the 3 speed, try reinserting the shaft into it. If it goes all the way, then the burr is on the tranny output shaft. Take the tailcone off & run your finger nail up & down all of the splines on both sides & all the way to the bottom of the grooves. The other possibility is that the output shaft is twisted near the center of the splined area.
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|