Wtb 3/4 Ton Dana 44 Spindles! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*72longbed* · 02-25-2005, 11:56 AM

Looking to buy a pair of GM Dana 44 3/4 ton disk brake axle spindles. 71/72 will work. Must be off a factory 3/4 ton, 8 lug, GM Dana 44 that has disk brakes.

I still have the original ones to compare measurements if necessary.

Anybody have a pair of these that are in great shape laying around??

Thanks,
72longbed

hugger67 · 02-25-2005, 11:05 PM

i've got a couple of sets i'll try a post a pic in a day or two

*72longbed* · 02-26-2005, 02:26 AM

hugger67,
sounds good, look forward to the pics.

Thanks,
72longbed

**kwmech** · 02-26-2005, 02:48 AM

71-75 should work if you have the 'bolt on' locking hubs.

*72longbed* · 02-26-2005, 02:59 AM

Check out this page for Spindle info, it's what I'm using to identify the right spindles that I need:

http://77cj.littlekeylime.com/flatop_knucles.html

About 1/3 of the way thru the page are pics of different spindles. I believe I need part #706570X. Says these were used on ALL GM 3/4 ton Dana 44's.

That's what I got.

Thanks for looking,
72longbed

drink2mny · 02-27-2005, 01:02 AM

How about 60.00 plus shipping??

02-25-2005, 11:56 AM	#1
72longbed Account Suspended Join Date: Jun 2003 Location: PA Posts: 1,411	Wtb 3/4 Ton Dana 44 Spindles! Looking to buy a pair of GM Dana 44 3/4 ton disk brake axle spindles. 71/72 will work. Must be off a factory 3/4 ton, 8 lug, GM Dana 44 that has disk brakes. I still have the original ones to compare measurements if necessary. Anybody have a pair of these that are in great shape laying around?? Thanks, 72longbed Last edited by 72longbed; 02-25-2005 at 12:02 PM.

02-27-2005, 01:02 AM	#6
drink2mny Registered User Join Date: Jun 2003 Location: spokane wa Posts: 2,189	How about 60.00 plus shipping?? Attached Images __________________ Support The Board

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

02-25-2005, 11:05 PM	#2
hugger67 Registered User Join Date: Jul 2002 Location: wisconsin Posts: 67	i've got a couple of sets i'll try a post a pic in a day or two

02-26-2005, 02:26 AM	#3
72longbed Account Suspended Join Date: Jun 2003 Location: PA Posts: 1,411	hugger67, sounds good, look forward to the pics. Thanks, 72longbed

02-26-2005, 02:48 AM	#4
kwmech Senior Member Join Date: Mar 2003 Location: Colfax-California Posts: 8,667	71-75 should work if you have the 'bolt on' locking hubs.

02-26-2005, 02:59 AM	#5
72longbed Account Suspended Join Date: Jun 2003 Location: PA Posts: 1,411	Check out this page for Spindle info, it's what I'm using to identify the right spindles that I need: http://77cj.littlekeylime.com/flatop_knucles.html About 1/3 of the way thru the page are pics of different spindles. I believe I need part #706570X. Says these were used on ALL GM 3/4 ton Dana 44's. That's what I got. Thanks for looking, 72longbed



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.