700r4 connections - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**guyryan100** · 03-07-2005, 02:22 PM

I installed the dipstick tube into my new 700r4 yesterday, and notice another hole about 3" behind the dipstick hole in the tranny. It has a similar rubber gromet on it. What's it for?

ac102nv · 03-07-2005, 03:03 PM

It's for the TV cable...assuming it the hole circled in the pic...

ac102nv · 03-07-2005, 03:05 PM

Do NOT fire up the engine until you get the TV cable installed/adjusted. Rumor has it you can burn up the trans in a matter of minutes without it!

smokekiki · 03-07-2005, 05:36 PM

Quote:

Originally Posted by ac102nv

Do NOT fire up the engine until you get the TV cable installed/adjusted. Rumor has it you can burn up the trans in a matter of minutes without it!

iT IS NOT A RUMOR.The tv cable regulates the fluid pressure.If not adjusted right it will overheat quickly.Go to www.700r4.com read about the tv.

Exille · 03-07-2005, 04:53 PM

make sure its a color tv cable, black and white tv cable wont work :P

**VetteVet** · 03-07-2005, 10:00 PM

Quote:

Originally Posted by guyryan100

I installed the dipstick tube into my new 700r4 yesterday, and notice another hole about 3" behind the dipstick hole in the tranny. It has a similar rubber gromet on it. What's it for?

guy I'm concerned about your post because you don't have a tv cable in your new tranny and you didn't say what it was going into or what setup You have. The other guys are correct saying that the tv cable has to be set up properly in order to shift right and to avoid damage. They are a little paranoid though because the tv cable will control line pressures for the shift points and until the trans is put into gear no fluid transfer will occur. The primary damage occurs when the transmission is in overdrive and the torque converter runs unlocked. This generates large amounts of heat and transfers to the clutch paks and if it exceeds 250 degrees it may damage them beyond repair. part of my concern is if you have the correct adapter for the tv cable mount at the carburetor. Thats why I asked you what application you were using. There are many useful sources of information about the 700r4 and how to setup the tv cable. The link above is one of them and there is a thread in the FAQs about them also.
Hope this helps.
Vettevet

**guyryan100** · 03-07-2005, 11:50 PM

Oh, of course. For some reason I was picturing the tv cable hookup on the drivers side. I have the TV made EZ kit on its way from BTO, and won't be connecting the flexplate until that kit is installed. Thanks for the info - got it now. We're not quite mobile yet, so I've got plenty of time to screw things up in the next couple of weeks :-)

03-07-2005, 02:22 PM	#1
guyryan100 Registered User Join Date: Sep 2001 Location: Cumming, GA Posts: 481	700r4 connections I installed the dipstick tube into my new 700r4 yesterday, and notice another hole about 3" behind the dipstick hole in the tranny. It has a similar rubber gromet on it. What's it for?

03-07-2005, 03:03 PM	#2
ac102nv Registered User Join Date: Jul 2004 Location: Northern Nevada Posts: 156	It's for the TV cable...assuming it the hole circled in the pic... Attached Images __________________ '72 C10 lwb 454/TH400

03-07-2005, 03:05 PM	#3
ac102nv Registered User Join Date: Jul 2004 Location: Northern Nevada Posts: 156	and one more thought.... Do NOT fire up the engine until you get the TV cable installed/adjusted. Rumor has it you can burn up the trans in a matter of minutes without it! __________________ '72 C10 lwb 454/TH400

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

03-07-2005, 04:53 PM	#5
Exille Registered User Join Date: Jan 2005 Location: Placerville Posts: 91	make sure its a color tv cable, black and white tv cable wont work :P

03-07-2005, 11:50 PM	#7
guyryan100 Registered User Join Date: Sep 2001 Location: Cumming, GA Posts: 481	Oh, of course. For some reason I was picturing the tv cable hookup on the drivers side. I have the TV made EZ kit on its way from BTO, and won't be connecting the flexplate until that kit is installed. Thanks for the info - got it now. We're not quite mobile yet, so I've got plenty of time to screw things up in the next couple of weeks :-)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.