5 point harness with factory buckets? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Low69CST · 03-31-2005, 01:36 PM

Does anyone think a 5 point racing harness would work properly without cutting holes in the factory buckets? The gastank is gone, so i can use that for some type of mounting system.

Mudder · 03-31-2005, 03:14 PM

The harness needs to be mounted at shoulder height, unless you use the proper seat. In a roll over shoulders belts can break your back if they are mounted to the floor. I have been thinking about getting seats so that I can use the shoulder belts. I would also like a cage inside the cab.

Low69CST · 03-31-2005, 03:17 PM

I heard that too about the shoulder straps. By using upper mounts for the gas tank, could you secure the shoulder straps to that and be fine?

Mudder · 03-31-2005, 03:29 PM

I wouldn't ever tell ya it'd be alright just in case you go out and break your back.

I don't need any lawsuits this week.... I'm thinkin as long as ya have the right kind of seats for shoulder belts and you dont snug em down real tight you'd be alright. I may be wrong. I'll prbably just wait till I do a cage in mine and then mount them to a cross bar.

Low69CST · 03-31-2005, 03:35 PM

I'm lookin to keep my factory seats, i'm just thinkin though.

Mudder · 03-31-2005, 04:04 PM

I'm just using rjs lap belts. They arent real comfy.........

03-31-2005, 01:36 PM	#1
Low69CST Registered User Join Date: May 2000 Location: Frankfort, Kentucky, USA Posts: 2,163	5 point harness with factory buckets? Does anyone think a 5 point racing harness would work properly without cutting holes in the factory buckets? The gastank is gone, so i can use that for some type of mounting system. __________________ '69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks

03-31-2005, 03:17 PM	#3
Low69CST Registered User Join Date: May 2000 Location: Frankfort, Kentucky, USA Posts: 2,163	I heard that too about the shoulder straps. By using upper mounts for the gas tank, could you secure the shoulder straps to that and be fine? __________________ '69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks

03-31-2005, 03:35 PM	#5
Low69CST Registered User Join Date: May 2000 Location: Frankfort, Kentucky, USA Posts: 2,163	I'm lookin to keep my factory seats, i'm just thinkin though. __________________ '69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

03-31-2005, 03:14 PM	#2
Mudder Registered User Join Date: Feb 2001 Location: East Central, MO Posts: 11,336	The harness needs to be mounted at shoulder height, unless you use the proper seat. In a roll over shoulders belts can break your back if they are mounted to the floor. I have been thinking about getting seats so that I can use the shoulder belts. I would also like a cage inside the cab.

03-31-2005, 03:29 PM	#4
Mudder Registered User Join Date: Feb 2001 Location: East Central, MO Posts: 11,336	I wouldn't ever tell ya it'd be alright just in case you go out and break your back. I don't need any lawsuits this week.... I'm thinkin as long as ya have the right kind of seats for shoulder belts and you dont snug em down real tight you'd be alright. I may be wrong. I'll prbably just wait till I do a cage in mine and then mount them to a cross bar.

03-31-2005, 04:04 PM	#6
Mudder Registered User Join Date: Feb 2001 Location: East Central, MO Posts: 11,336	I'm just using rjs lap belts. They arent real comfy.........



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.