pics for hotrodmtodd (I hope ) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

biglou55 · 06-02-2005, 08:49 AM

two of these pics are upside down hope they help you.

midyearvet@aol. · 06-02-2005, 10:11 AM

Never seen one like that.
Rick / Ca.

hotrodmtodd · 06-02-2005, 02:13 PM

Lou,
That is EXACTLY what I needed to see! I will NEVER be able to thank you enough for this my friend. Now all I can do is hope and pray that your car club friend has no use for that stuff. If he DOES need it, maybe I can get you to measure the width on that bellcrank (z-bar) and maybe trace an outline of that bracket. I guess it all depends on what engine/tranny he is going to use. If he is using an automatic that would solve everything! If he is sticking with the 4-speed, but using a small block, I have ALL the correct brackets and linkage for that application so maybe he and I could swap. Please let me know his decision, and thank you SO MUCH again. Take care, Mike

Edit: One other thing I can see, my headers are going to have to go. If your buddy with the motor is not going to use those manifolds, I would probably be interested in them if they are reasonable. Otherwise, maybe you could get me a casting # from them so that I could find a set down here in PA. Thanks.

biglou55 · 06-02-2005, 02:19 PM

Todd we belong to the northeast chevy\gmc truck club but i will check with him on the parts. I will let you know.

06-02-2005, 08:49 AM	#1
biglou55 Senior Member Join Date: Sep 2002 Location: Greenfield Mass. Posts: 551	pics for hotrodmtodd (I hope ) two of these pics are upside down hope they help you. Attached Images __________________ Certifiably crazy person

06-02-2005, 10:11 AM	#2
midyearvet@aol. Registered User Join Date: Jun 2003 Location: Napa, Ca. Posts: 103	Block Bracket Never seen one like that. Rick / Ca.

06-02-2005, 02:13 PM	#3
hotrodmtodd 'Burban Legend Join Date: Apr 2005 Location: Mingo Junction OH Posts: 918	Yes! Yes! Yes! Lou, That is EXACTLY what I needed to see! I will NEVER be able to thank you enough for this my friend. Now all I can do is hope and pray that your car club friend has no use for that stuff. If he DOES need it, maybe I can get you to measure the width on that bellcrank (z-bar) and maybe trace an outline of that bracket. I guess it all depends on what engine/tranny he is going to use. If he is using an automatic that would solve everything! If he is sticking with the 4-speed, but using a small block, I have ALL the correct brackets and linkage for that application so maybe he and I could swap. Please let me know his decision, and thank you SO MUCH again. Take care, Mike Edit: One other thing I can see, my headers are going to have to go. If your buddy with the motor is not going to use those manifolds, I would probably be interested in them if they are reasonable. Otherwise, maybe you could get me a casting # from them so that I could find a set down here in PA. Thanks. __________________ '67 Chevy Iron City Beer Truck (9ft step) '67 Chevy Panel Truck 467 '68 Short Fleet 305v6 '68 McLaren Ramp Truck '68/'68/'70/'71 Burbs 292/366/402/454 '69 C-30 dump '71 C-50 dump and church bus '71 4x4 454 '72 Blazer (w/pop-up camper) $15 x-hooks '66 Chevy II 194/Weber '68 El Camino" 305v6 '69 Skylark 455 Buick '70 Chevelle 427 '71 Cutlass W-31 '71 GTO 400 2x2 "The 51" Chopped '51 Chevy (409) my first car OK Toad, we'll take 'em all... John Milner Last edited by hotrodmtodd; 06-02-2005 at 02:23 PM. Reason: Additional Comment

06-02-2005, 02:19 PM	#4
biglou55 Senior Member Join Date: Sep 2002 Location: Greenfield Mass. Posts: 551	Todd we belong to the northeast chevy\gmc truck club but i will check with him on the parts. I will let you know. __________________ Certifiably crazy person

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.