The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-15-2005, 02:27 AM   #1
Daks
I like crayons
 
Daks's Avatar
 
Join Date: Feb 2005
Location: Colorado Springs, CO
Posts: 80
Mess of questions...

I am in the middle of performing a swap to big block in my 72 Cheyenne K20 with little to no knowledge on what this really takes to accomplish...

As I understand it from everything I have been able to gleen from the boards here is I need to move the entire drive train forward a little bit in order to gain the clearance that I need to make things fit. Well, I have a couple options and questions that I was hoping someone might be able to give some insite into...

I have an trade out where I can get a 700R4 tranny for a littlle side work that is being completely rebuilt and was thinking about using it for the overdrive. As I understand it, the 700R4 is about 2" longer then a TH350. Can I just bolt that 700R4 directly to my np205, use the 2" in lenght difference to place my engine far enough out front to clear everything without making a headache (or more of a headache as I have learned...) with headers? Or do I need to change the shafts and get spacers and mess with drive shafts and all of that... At one point, I saw a decent thread that had some info on a 700R4 in a 4x4 truck, but I can find it anylonger... Also, does this mean that I have to move the engine stands farther forward as well to make this work? Or mess with any of the cross members?

If I stay with my TH350, do I need to do anything besides moving things forward a little bit? I do not really want to mess with changing the sizes on the drive shafts... And I definitely do not want to be beating in the firewall to get this to work.

You have to forgive me, I really know very little about engines, and working on any automobile, but I tell you... this working in the grease, barking your nuckles, and trying to figure out what the hell your doing is the most fun I have had in a long long time. =) Any help and insight would be greatly appreciated.

Thanks!

Last edited by Daks; 06-15-2005 at 02:29 AM. Reason: bleh, forgot a piece.
Daks is offline   Reply With Quote
Old 06-15-2005, 05:45 AM   #2
4x4Poet
Registered User
 
Join Date: Nov 2004
Location: "Under Montana skies."
Posts: 1,836
I can give you a philosophical approach (i.e., wordy). Since the driveshafts can easily be shortened or lengthened and the tranny crossmember can be slid forward or rearward with new holes drilled thru the frame, the more crucial placement involves having enough fan clearance before the radiator and valve cover clearance in front of the firewall. Work those out first before drilling eng crossmember or tranny xmember holes in the frame. You also potentially can use a big block or 2wd fan shroud instead of the 4x4 (K10/K20) shroud that extends farther back than the other two.

As for avoiding driveshaft work, how close you can get to the original holes in the tranny crossmember without having to bash the firewall or place the fan too close or to far from the radiator is probably anybody's guess. Maybe someone here knows. We have had a few folks put BBCs in 67-72 4x4s.

BTW, in your research did you read of using a 73-8? engine crossmember instead of the stock, K20 eng xmember? The 73up eng xmember bolts right up with only a few extra holes to drill and it eases and expands oil pan choices. Uses the common clam shell motor mounts, too. Of course, it can be placed foward or aft of the original eng xmember to some degree. I don't know how it would affect engine placement if left in the original position.

Glad you're having fun.
__________________
'71 GMC K20 Suburban, '71 GMC K10 Suburban, '72 Chevy C10 CST Suburban, '72 Chevy K20 clunker pickup.

Last edited by 4x4Poet; 06-15-2005 at 05:48 AM.
4x4Poet is offline   Reply With Quote
Old 06-15-2005, 06:06 AM   #3
GMC AMI
Registered User
 
GMC AMI's Avatar
 
Join Date: Apr 2004
Location: The Other Maine!
Posts: 2,236
Wink BB swap.

I exchanged a 350 with a 396 from a car and bolted it right in with the only mod was cutting the 4x4 shroud down to size. This was a 71 GMC 4x4 1/2 ton.
__________________
1968 Chevy 4x4 307 4 speed
GMC AMI is offline   Reply With Quote
Old 06-15-2005, 09:55 AM   #4
Yukon Jack
Post Whore
 
Yukon Jack's Avatar
 
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
I put a 454 in my 69 K20 using the existing small block engine crossmember and towers along with new stock type engine mounts. Oil pan clearance was very close. I ended up using a couple washers to raise up the engine slightly. I had major firewall interference even with a body lift.

If I were to do it over I would definitely move the engine forward and then work through moving the transfer case and tranny. A problem with moving the engine forward is you are shortening the front driveshaft. You want it to be as long as possible to keep the angle from being too severe. If you used a longer tranny that would help.

You will find some people have installed bb's in the K trucks with absolutely no modifications. Some just need to massage the firewall a little, others like me have to make major firewall modifications. Don't ask me why it varies.

Burt4x4 recently put a bb in his K5 and just had to do minor firewall mods. He has a body lift and he did switch to the 73-up crossmember. You might want to pm him so he can chime in with his thoughts.

I don't have info on the tranny to transfer case issue but I would imagine you will need some type of adapter to use that tranny with an NP205.
__________________
1970 Blazer with a 400 sbc and 4" lift
1980 Pontiac Trans Am, 455 Oldsmobile
2012 Kawasaki Concours 14
Yukon Jack is offline   Reply With Quote
Old 06-15-2005, 06:16 PM   #5
ckhd
Registered User
 
ckhd's Avatar
 
Join Date: Oct 2000
Location: St. Johns, Arizona
Posts: 2,660
Well, here's my 2¢. I haven't done both at the same time, but I have put a big block in a 4 wheel drive, and I have put a 700r4 in a 4-wheel drive. I *might* have done the post with the 700r4 conversion. I made a big long one with all my troubles/experiences with it after I did it.

My experience with a big block in a 4-wheel drive and no 700r4 (In a '72 K5): There are major firewall issues. We had to "massage" the firewall with a big hammer until it fit. After that, all is well. Used the same motor mounts and everything.

My experience with a 700r4 and a small block: I moved the engine forward. It's 1 3/4" if I remember right. I did have to trim the fan shroud to let the power steering pump fit, and the radiator hoses. It took drilling 8 holes for the new location of the crossmember. I was originally going to do the driveshaft deal, but two things made me change my mind. First, the transfer case mount looked like it was going to be way to big of a headache for me to relocate, plus I was low on funds and didn't want to have to pay for driveshaft mods. Second, I would like to someday put in a big block, and remembering the experience I had with the '72 blazer, I decided that moving it forward would allow the clearance needed to put a big block in.

So, in my opinion, move the mounts forward, leave the driveshaft alone. You will gain the needed firewall clearance, and you won't have to jack with driveshafts, tranny mounts, and t-case mounts.
__________________
my 2¢ - t.i.o.l.i.
Bowen

1968 K20 fleet
1969 K10 swb fleet
1972 K10 Suburban
1972 C10 lwb step
1992 K1500 'burb
1995 K2500 'burb
1997 C1500 'burb
1999 K1500
2000 K1500 'burb

Why do I own so many Suburbans?
ckhd is offline   Reply With Quote
Old 06-15-2005, 06:22 PM   #6
ckhd
Registered User
 
ckhd's Avatar
 
Join Date: Oct 2000
Location: St. Johns, Arizona
Posts: 2,660
Forgot to address the 700r4 to the 205 issue:

It will not bolt right up. The reason is the output shaft on the 700r4.

If you have a NP205 from an automatic pickup, you can get an output shaft that will allow you to bolt it right up. When I did my 'burb, I bought the tranny with the output shaft already installed (I got mine from Bowtie Overdrives). It did literally bolt right up. No mods, no worries. I have no idea if anyone makes a 700r4 output shaft that will spline with a 205 from a manual transmission pickup.

Bowtie Overdrives, and Advanced Adapters both sell the output shaft seperately. I don't know who else does. When I found out B.O. had the shaft, I stopped looking.
__________________
my 2¢ - t.i.o.l.i.
Bowen

1968 K20 fleet
1969 K10 swb fleet
1972 K10 Suburban
1972 C10 lwb step
1992 K1500 'burb
1995 K2500 'burb
1997 C1500 'burb
1999 K1500
2000 K1500 'burb

Why do I own so many Suburbans?
ckhd is offline   Reply With Quote
Old 06-15-2005, 07:06 PM   #7
402Bowtie
Registered User
 
402Bowtie's Avatar
 
Join Date: Sep 2003
Location: Wichita, KS
Posts: 3,735
Is this the thread you were looking for?
700R4 w/ NP205
402Bowtie is offline   Reply With Quote
Old 06-16-2005, 02:13 AM   #8
Daks
I like crayons
 
Daks's Avatar
 
Join Date: Feb 2005
Location: Colorado Springs, CO
Posts: 80
Ooh, thanks for all the great information, I do have a couple more things I am having trouble with resolving that I couldnt dig out during the course of reading the threads and replies here. I am feeling a bit more confident about actually doing this now then I was yesterday hehe.

So.. If I go with the 700R4, it should put the front crossmember out to a position that will work just fine for the big block. Also I should be able to just use the same tail end of the 350 I have now. And as the 700R4 is being rebuilt, I can tell em to just put a 4x4 output shaft on it so I dont need to make any modifications to anything else. At least this is the picture I gathered...

Now, in regards to shifting linkage geometry.... Should this all remain the same and I dont need to mess with that stuff at all? The kickdown should work the same as with the 350 I assume, as well as the fluid tube? I guess since I have just a 3 speed column indicator that the linkage probly does need to change, any suggestions on that?

Thanks again for the great knowledge base you all share openly!
Daks is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:19 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com