![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
![]() Join Date: Apr 2005
Location: Ar
Posts: 558
|
Decision Time 84gmc Headache or 84chevy Bigblock Potential Headache
I already have a brown 84gmc shortbed which consist of a woreout 305(headers and flowmasters already installed) decent paintjob but needs a few dings ironed out of the metal to look better. Interior needs dash and carpet and has a 50cent piece hole in driver side seat. defrost not blowing up top at the windsheild but a/c ran until compressor started acting funny so with new compressor should blow cold again. I replaced the right side vent window(it was laying in floor when purchased) but the left side seeps a little wind as well. Power window/locks windows work, power locks only work manually. Tranny shifts fine but has slight leak (no biggie). All I have in it now is 1500 plus the cost of the flowmaster exhaust/rebuilt starter, so it's a decent project truck.
I'm at the point of buying a 350 crate motor(money in hand) and yesterday I go out for one last peep for maybe something a little easier to get going. I found a brown 84 chevy shortbed. Wow another brown my luck! Heres the goodies and uglies with a 15min survey of the truck. Big block not sure the size guessing 454 clean under the hood so not sure on the milage, headers, flowmasters, 750 edelbrock, edel intake, not sure what size tranny, no a/c(missing lines and compressor). The motor swap almost looks like it came from the factory with the exception of minor bends in headers to clear frame. Interior is clean, carpet not worn could use some die, dash is good but missing a/c vents, seat in really good condition, good door panels, manual window/locks. Exterior is all str8 except one blemish on the passenger door the size of your hand. It looks to have replacement front fenders lft and rht side and metal cowl induc hood. Hood and fenders need prime and paint. Truck is lowered maybe 3/4 drop and it has 20in. rims and tires. The driverside door doesn't open, figures with my lucky findings. The guy(lot) is asking $4200 for the truck, but I might be able to get the price lower. I don't need the 20's and the inoperable door I might be able to get him down to maybe $3500. I suppose thats enough info ![]() ![]() |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jul 2003
Location: Indianapolis, IN
Posts: 1,277
|
It would be hard for me to get excited about the big block if you intend to drive the truck very much. You would also need to get the fenders and hood in paint fairly soon, before they rust away. The new fenders may mean a truck that has more rust hiding, like in the cab or core support.
One way to take the emotion out of it is run the numbers and see what the costs for fixing what you have are compared to the purchase and of the new truck. |
![]() |
![]() |
![]() |
#3 |
Born a Chevy Man
Join Date: Apr 2005
Location: Navarre, Florida
Posts: 10,221
|
You woud proberly be better off just fixing what you have and installing the 350. $4,200.00 sounds pretty high. Be better if you could get him to lower the price. Any way that is what I would do if you do like the truck you now have. Just fix yours up a little at a time.
__________________
John or 86 (Viet Nam combat Vet-BIG RED ONE) '65-'66 *1986 Chevy SWB Silverado *1984 Chevy Longbed Silverado New Kia Sportage (Wife's car and she loves it) ![]() ![]() If you can read this, YOU NEED TO THANK A TEACHER! If you can read this in ENGLISH, PLEASE THANK A SOLDIER! ![]() GOD BLESS AMERICA AND BLESS OUR FIGHTING TROOPS |
![]() |
![]() |
![]() |
#4 |
No No
Join Date: Jun 2005
Location: Pueblo Colorado
Posts: 1,781
|
I'd pass on it. Take the money and fix your truck the way you want it. $3500, what your willing to spend on another truck will go a long way with somthing you already own. If you want some umph under the hood dont bother with a crate 350 find a built 400 and eat a core.
__________________
1976 Custom Deluxe SWB Med FMB.3/4 Drop. Gen VI 454, Muncie HD 3 speed With Modified OE Hurst Shifter, 3.73 12 bolt, GMPP HO roller cam, Hooker headers, Performer intake with modified Q-jet, Accel distributor. Best 1/4 12.3 @108. Funnest run 19.84 @88 full 1/4 mile burn out. 1997 K1500 ext cab 5.7 stock except muffler |
![]() |
![]() |
![]() |
#5 |
Happy to be here
![]() Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
|
Keep yours! It may need some work, but you already know what it needs. Don't let the flash of 20" wheels and a 454 cause you to over see other concerns. If the front end is fresh and the door won't open it sounds like it was wrecked and wasn't repaired properly. I wouldn't even consider it unless it was so cheap that you could get past the possibility of hidden damages.
Spend the money on your truck and be much better off.... ![]()
__________________
Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" |
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: Apr 2005
Location: Ar
Posts: 558
|
Thanks guys some of those same thoughts went threw my mind.
|
![]() |
![]() |
![]() |
#7 |
Happy to be here
![]() Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
|
Sometimes all you need is someone to point out the problems that you don't want to admit to your self. Glad we could help....
![]() |
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Jan 2003
Location: Atlantic City, NJ
Posts: 1,073
|
Take your money and buy a zz502 crate.
__________________
86 SWB 9.0 LITER T-400-OD 4.11 eaton-4/5 drop Best 1/4 12.51 @112mph no traction ![]() |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|