door adjustment - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hasch Yaeger · 07-22-2002, 12:32 PM

I reworked a 72 4x4 pick up truck a few years ago. I put new floor pans in it and cab supports. I took the doors off so I could work better. I had to move the truck in & out of the garage a couple of times because of other work I had going on at the same time. The cab moved slightly and the doors never fit the same. I’m sure their use to be a special wrench to get to the body side of the hinge bolts, but by now it’s probably not available. I’d rather make one of my own anyway. Does anyone out there have a picture of something like this?
Actually, I think it will take more that just adjusting hinge adjustment. Does anyone have any suggestion?
Thanks!!

*Randy70C-10* · 07-22-2002, 12:41 PM

The only way I know how to adjust the doors is with the fenders off.

Woody · 07-22-2002, 01:30 PM

You need a 'S' shaped boxed end wrench and plenty of patience.

7069684X4 · 07-22-2002, 01:44 PM

I used a wrench that has a socket on one end and an open end on the other. Still scratched it though.

JimKshortstep4x4 · 07-22-2002, 02:08 PM

Depending on which way your adjustment needs to go and whether or not the hinges are good, you might try shimming the front cab mounts. If you raise the right side, it will in effect bring the left side up and vice versa.

Jim

photoglg · 07-22-2002, 10:42 PM

I bought the S wrench from snap-on they still sell it, but very costly about $ 54.00 the part number is S9619

Erl · 07-23-2002, 10:39 AM

Sears sells an "obstruction wrench" for $16. It is C shaped and will do the job.

07-22-2002, 12:32 PM	#1
Hasch Yaeger Registered User Join Date: Jul 2002 Location: pa Posts: 3	door adjustment I reworked a 72 4x4 pick up truck a few years ago. I put new floor pans in it and cab supports. I took the doors off so I could work better. I had to move the truck in & out of the garage a couple of times because of other work I had going on at the same time. The cab moved slightly and the doors never fit the same. I’m sure their use to be a special wrench to get to the body side of the hinge bolts, but by now it’s probably not available. I’d rather make one of my own anyway. Does anyone out there have a picture of something like this? Actually, I think it will take more that just adjusting hinge adjustment. Does anyone have any suggestion? Thanks!!

07-22-2002, 10:42 PM	#6
photoglg Registered User Join Date: Jul 2001 Location: Oxnard, CA Posts: 143	I bought the S wrench from snap-on they still sell it, but very costly about $ 54.00 the part number is S9619 __________________ 1969 GMC S/B S/S 3" drop

07-23-2002, 10:39 AM	#7
Erl Registered User Join Date: Mar 2002 Location: Dallas, TX Posts: 555	Sears sells an "obstruction wrench" for $16. It is C shaped and will do the job. __________________ 1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

07-22-2002, 12:41 PM	#2
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	The only way I know how to adjust the doors is with the fenders off.

07-22-2002, 01:30 PM	#3
Woody Registered User Join Date: Feb 2000 Location: Georgetown, KY, USA Posts: 631	You need a 'S' shaped boxed end wrench and plenty of patience.

07-22-2002, 01:44 PM	#4
7069684X4 Registered User Join Date: Jul 2002 Location: Fla Posts: 29	I used a wrench that has a socket on one end and an open end on the other. Still scratched it though.

07-22-2002, 02:08 PM	#5
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Depending on which way your adjustment needs to go and whether or not the hinges are good, you might try shimming the front cab mounts. If you raise the right side, it will in effect bring the left side up and vice versa. Jim



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.