|
|
|
04-03-2006, 03:14 PM
|
#1 |
|
Registered User
Join Date: May 2004
Location: Topeka, Ks
Posts: 2,293
|
Cruise control (EBAY)
__________________
I'm not a pessimist, I'm just optimistic that bad things are going to happen. 1971 Cheyenne Super K10 - tilt, cruise, air, am/fm, tow hooks, factory buckets! 1986 Jeep J10 pickup, - 5.3L Vortec with 4L60e and NP241. |
|
|
|
04-03-2006, 04:08 PM
|
#2 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
|
Re: Cruise control (EBAY)
Chip... FYI, that is a 71 only set up, and I think the turn signal switch may be wrong... in 72 it was located under the dash.
|
|
|
|
|
04-03-2006, 05:13 PM
|
#3 |
|
computer illiterate
Join Date: Jan 2001
Location: Des Moines, IA
Posts: 6,440
|
Re: Cruise control (EBAY)
can you make me a copy of the instructions?
__________________
72 2wd blazer 72 swb 4x4 |
|
|
|
|
04-03-2006, 08:27 PM
|
#4 |
|
Senior Member
Join Date: Nov 2003
Location: Calgary Alberta
Posts: 1,936
|
Re: Cruise control (EBAY)
I have the 72 cruise control, does anyone have a diagram of the entire system, Im not sure what Im missing.
Sorry to steal your thread. Good luck with the sale, Im watching to see what they will go for . Darren
__________________
67- 72 Parts collecter |
|
|
|
|
04-03-2006, 09:19 PM
|
#5 |
|
Join Date: Dec 1999
Location: Eastern - Manitoba Canada, Winnipeg
Posts: 4,369
|
Re: Cruise control (EBAY)
Looks 71-72 to me.....except the switch is newer, but will work.
__________________
Senior active founding member. 70 3/4 ton GMC Suburban 4x4 250/4 spd. 71 1/2 ton Suburban Chevy 4x4, 350/350 72 Chev 1 ton tow truck 402BB w/Holmes 440 wrecker on propane 2005 FLSTSCI Harley Springer 85 FXSB Harley Lowrider 72 Triumph 650 Bonneville 5spd "Poor people don't have hobbies" Quote from wife. |
|
|
|
|
04-03-2006, 09:41 PM
|
#6 |
|
Registered User
Join Date: May 2004
Location: Topeka, Ks
Posts: 2,293
|
Re: Cruise control (EBAY)
I thought it was 71-72, all of the parts included look just like the parts in the directions, except for the switch. I do have the underdash switch but will not be parting with it, saving it for mine.
 Jeff
__________________
I'm not a pessimist, I'm just optimistic that bad things are going to happen. 1971 Cheyenne Super K10 - tilt, cruise, air, am/fm, tow hooks, factory buckets! 1986 Jeep J10 pickup, - 5.3L Vortec with 4L60e and NP241. |
|
|
|
|
04-03-2006, 10:38 PM
|
#7 |
|
Registered User
 
Join Date: Feb 2004
Location: Idaho
Posts: 4,033
|
Re: Cruise control (EBAY)
Could you please scan those instructions before you ship the cruise control set up out, There are alot of board members who would thank you dearly for those instructions
Thanks Michael
__________________
"Remember, They can Kill You, but they can't eat You, That's against the law!!!!!!!!!" |
|
|
|
|
04-03-2006, 11:03 PM
|
#8 |
|
Just like to part out trucks!!
Join Date: Nov 2001
Location: Meriden, Ks-North of Topeka 10 miles
Posts: 27,395
|
Re: Cruise control (EBAY)
I'd buy if you install it for me in my blazer!!!!!!!!!
 NICE setup you have Jeff!!!
__________________
67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure" |
|
|
|
|
04-04-2006, 10:28 AM
|
#9 |
|
Registered User
Join Date: Aug 2001
Location: Rocky Mount, MO
Posts: 1,293
|
Re: Cruise control (EBAY)
Could use the instructions also
|
|
|
|
|
04-04-2006, 11:20 AM
|
#10 |
|
Jamie Hyneman is my twin
 
Join Date: Nov 2005
Location: La Junta, Colorado
Posts: 705
|
Re: Cruise control (EBAY)
If you post the instructions, I'll make a color wiring diagram. You can send scans to boundstaffpress@yahoo.com
__________________
Justin SOLD 1967 K10 Fleetside, 283, Front and Rear Posi SOLD Color Wiring Diagrams Now in High Resolution V8 and Cab and Cab and Chassis |
|
|
|
|
04-04-2006, 11:42 AM
|
#11 |
|
Account Suspended
Join Date: Nov 2005
Location: ILLINOIS
Posts: 145
|
Re: Cruise control (EBAY)
Yeah please scan and post those instructions for the archives I have no use for them but think they would be useful for the future..
Thanks |
|
|
|
|
04-04-2006, 01:35 PM
|
#12 |
|
Senior Member
Join Date: Oct 2005
Location: Austin, TX
Posts: 1,229
|
Re: Cruise control (EBAY)
ooh yeah, instructions after the sale...please!
__________________
"Anybody who would paint his truck like this, would go to a minister's funeral dressed in feathers!" - Big Enis Burdett '72 Blazer Restoration Blog: http://sportchicken.blogspot.com/ |
|
|
|
|
04-04-2006, 07:07 PM
|
#13 |
|
Not a bad nut after all..
Join Date: Dec 2000
Location: ND
Posts: 1,759
|
Re: Cruise control (EBAY)
Instructions also, please.
__________________
'05 Chevy 2500HD 4x4 '72 GMC LWB 4x2 driver '72 Chevy LWB 4x4 plow truck '71 Blazer 4x4 driver '70 GMC LWB trailer |
|
|
|
|
04-04-2006, 08:58 PM
|
#14 |
|
Registered User
Join Date: Nov 2003
Location: Lincoln NE
Posts: 89
|
Re: Cruise control (EBAY)
So I take it this could be put on a Non Cruise Truck no problem?
|
|
|
|
|
04-04-2006, 10:29 PM
|
#15 | |
|
Registered User
Join Date: May 2004
Location: Topeka, Ks
Posts: 2,293
|
Re: Cruise control (EBAY)
Quote:
I have the directions scanned and in pdf form and would be happy to share them when I get time. Jeff
__________________
I'm not a pessimist, I'm just optimistic that bad things are going to happen. 1971 Cheyenne Super K10 - tilt, cruise, air, am/fm, tow hooks, factory buckets! 1986 Jeep J10 pickup, - 5.3L Vortec with 4L60e and NP241. |
|
|
|
|
|
04-05-2006, 01:51 AM
|
#16 |
|
Senior Member
 Join Date: Mar 2000
Location: Rockville,In. USA
Posts: 3,721
|
Re: Cruise control (EBAY)
Guys you'll find 13 pages of instructions and installation information for the original cruise controls in Section 15 ( Accessories ) of any of the Chevy & GMC Service manuals for 1976-72 Chevy & GMC trucks, they show installation, electrical schematics, detailed drawings, and troubleshooting of entire system.
GMCPaul |
|
|
|
|
04-05-2006, 09:58 AM
|
#17 | |
|
Senior Member
Join Date: Oct 2005
Location: Austin, TX
Posts: 1,229
|
Re: Cruise control (EBAY)
Quote:
can any of the parts be purchased aftermarket (aside from the periodic ebay auction?) anything from another gm vehicle that would be similar? it'd be nice to have an original-ish setup instead of some audiovox on the dash with double-sided foam tape, etc.
__________________
"Anybody who would paint his truck like this, would go to a minister's funeral dressed in feathers!" - Big Enis Burdett '72 Blazer Restoration Blog: http://sportchicken.blogspot.com/ |
|
|
|
|
|
04-05-2006, 02:32 PM
|
#18 |
|
Registered User
Join Date: Jan 2006
Location: PA
Posts: 69
|
Re: Cruise control (EBAY)
I belive the under dash switch was 72 only. If you look at 1971 Chev Service Manual 10-30 series. Section 15 15-1 Cruise-Master Units. The Engagement Switch. It said it was located at the end of the directional signal lever. The 72 Service Manual does not have a section on Cruise Control. I was told this was because it was the one dealer installed. And that way it had a under dash switch.
|
|
|
|
|
04-05-2006, 03:25 PM
|
#19 |
|
Senior Member
Join Date: Oct 2005
Location: Austin, TX
Posts: 1,229
|
Re: Cruise control (EBAY)
well, i do have the cruise switch on the end of the turn signal lever (van column) so i guess i would need info for a '71. mine is a '72, and i only have the '72 service manual. would anyone be willing to scan the sheets from the '71 service manual particular to the turn signal switch? it would be appreciated. it looks like maybe the sheets chipflyer has would be the ones?
__________________
"Anybody who would paint his truck like this, would go to a minister's funeral dressed in feathers!" - Big Enis Burdett '72 Blazer Restoration Blog: http://sportchicken.blogspot.com/ |
|
|
|
|
04-09-2006, 06:54 PM
|
#20 |
|
Cantankerous Geezer
Join Date: Aug 2002
Location: Bel Aire, KS
Posts: 6,264
|
Re: Cruise control (EBAY)
4 hours left and the price is $350. Too bad you don't have a few more in the closet, you might be able to quit your day job.
__________________
Fred There is no such thing as too much cam...just not enough engine. 
|
|
|
|
|
04-10-2006, 12:24 AM
|
#21 |
|
Senior Member
Join Date: Apr 2000
Location: Oregon
Posts: 2,512
|
Re: Cruise control (EBAY)
ended at $455. Good sale.
To clarify these GM cruise units is there a specific manufacturer or are the parts stamped GM? I might be documenting mine and want to know differences and similarities with aftermarket ones. Would a factory unit be on glove box list?
__________________
Bob |
|
|
|
|
04-10-2006, 06:36 PM
|
#22 |
|
Registered User
Join Date: Feb 2004
Location: Tacoma WA
Posts: 1,365
|
Re: Cruise control (EBAY)
WOW - what a price.
Cheyenne10 - The set-up I have is not branded or numbered GM. The fender bracket and transducer have no GM logo's or numbers. The transducer says AC. The servo bellows and pully has no numbers. The wire harness has the little tape with a number (just like the lighter or radio harnesses should have when original). The small pedal bracket has no number. The entire set-up is uniquely GM in design and appearance - aftermarket sets(Holley) are very different. I feel very confident in calling mine a "factory installed cruise control" because I removed it from a 68 GMC pickup with the glove box listing. I will probably never find the correct switch/turn signal but will use a van style switch. My set-up is not for sale. Please do not inquire. Thank you - Bob
__________________
67 C-20 LWB, tilt, speed alert, vac, 454, T400 67 C-10 SWB, factory air with more to follow |
|
|
|
|
04-10-2006, 07:00 PM
|
#23 |
|
Registered User
Join Date: Sep 2005
Location: Colorado
Posts: 1,077
|
Re: Cruise control (EBAY)
I have a 1970 GMC that has factory cruise control. I will try to look at the parts for GM part numbers etc. It does show up as an option on the glove box sticker as you can see. For 1970 the cruise actuator switch is located on the turn signal mast. My turn signal mast is not in great shape so I have been on the look out for a replacement. I believe this same exact turn signal actuator was used well into the mid and maybe even late 1970's on trucks and Blazers and Suburbans. Not sure exactly how far. I would also like to see the installation instructions because my cruise has not been hooked up since PO installed the 700R4 transmission.
__________________
James |
|
|
|
|
04-10-2006, 10:45 PM
|
#24 |
|
Registered User
Join Date: Jan 2006
Location: PA
Posts: 69
|
Re: Cruise control (EBAY)
jimerie If you have 1970 chev truck chassis service manual 10-30 series. Section 15 Accessories Cruise Master it might be some help to you. The 1972 Cruise Master is a lot different then the 70. The 70 uses a servo mounted on firewall in back of carb.and uses a chain to pull on carb. The 72 servo mounts on inner fender wellon the drivers side and has a cable which head back towards firewall ,bends in a U and runs forward to carb. To pull on linkage. It also uses a different linkage adapter at the carb for the chain then it does for the cable.
|
|
|
|
|
04-10-2006, 11:09 PM
|
#25 |
|
Registered User
Join Date: May 2004
Location: Topeka, Ks
Posts: 2,293
|
Re: Cruise control (EBAY)
Here is a link to a discussion in the FAQ section from awhile back that has a lot of info about the cruise controls that were used on 67-72 trucks.http://67-72chevytrucks.com/vboard/s...d.php?t=136867
__________________
I'm not a pessimist, I'm just optimistic that bad things are going to happen. 1971 Cheyenne Super K10 - tilt, cruise, air, am/fm, tow hooks, factory buckets! 1986 Jeep J10 pickup, - 5.3L Vortec with 4L60e and NP241. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
