putting a nv3500 in a 67-72 c-10 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jamon8 · 07-04-2006, 10:37 AM

first of all you have to make provisions for the clutch pedal.
I cut the firewall in the 89 donor truck and welded it in place on my 69 c-10

jamon8 · 07-04-2006, 10:39 AM

then you have to cut the bottom of the cowl inside the cab so the clutch assembly will fit

jamon8 · 07-04-2006, 10:41 AM

then cut a hole in the floorboard. You can get the general idea from the placement in this picture

jamon8 · 07-04-2006, 10:45 AM

nest move the crossmember back about 3 inches
the bolt holes were predrilled in my frame. and cut a slot between the two holes in the bottom of the 350 crossmember so you can put the nv3500 trans mount through and have a bit of room for adjustments

jamon8 · 07-04-2006, 10:54 AM

a shortshaft 350 driveshaft works on a shortbed if you change the front yoke.
the Nv3500 is about the same size as a 350.

I put it behind a pre 87 small block so I had to get the older style flywheel to make it work

I suggest changing the clutch fork and the slave cylinder because these were week spots in the gm design. also make sure to use sycromesh in the tranny

Ask what you will, I will try to get back to you guys in a timely fashion!

Old Yeller 1970 · 07-04-2006, 11:05 AM

Hey jamon8 glad to see the write up. Congrats on a job well done.

Brad · 07-04-2006, 05:09 PM

Thanks for the write-up. I assume you did this with a V8?

chevytrucks79 · 07-04-2006, 05:25 PM

Thanks for the report and the pictures. My crossmember is all the way to the front like it last had a smaller 3 speed in it. It looks to me I am going to have to take it back further, if it will even work. I will probally have to make or find one that will work.

chevybill · 07-04-2006, 11:49 PM

I am using this tranny also. Do you have any pics of the pedal setup inside the truck? Did this tranny come out of a full size truck?(shifter location looks perfect) I have this tranny with a vortec 350 on tubular motor mounts in the v 8 position and I was able to use my stock driveshaft. My particular tranny came from a 4.3 s-10 so the shifter looks to sit further back than yours.

Thanks so much for posting this.

chevybill · 07-05-2006, 09:48 PM

Can you provide pics of the pedals mounted inside the cab?

jamon8 · 07-06-2006, 08:10 AM

you guys will have to wait a while for that because I am in the process of painting the cab!

07-04-2006, 10:37 AM	#1
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	putting a nv3500 in a 67-72 c-10 first of all you have to make provisions for the clutch pedal. I cut the firewall in the 89 donor truck and welded it in place on my 69 c-10 Attached Images

07-04-2006, 10:39 AM	#2
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: putting a nv3500 in a 67-72 c-10 then you have to cut the bottom of the cowl inside the cab so the clutch assembly will fit Attached Images

07-04-2006, 10:41 AM	#3
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: putting a nv3500 in a 67-72 c-10 then cut a hole in the floorboard. You can get the general idea from the placement in this picture Attached Images

07-04-2006, 10:45 AM	#4
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: putting a nv3500 in a 67-72 c-10 nest move the crossmember back about 3 inches the bolt holes were predrilled in my frame. and cut a slot between the two holes in the bottom of the 350 crossmember so you can put the nv3500 trans mount through and have a bit of room for adjustments Attached Images

07-04-2006, 10:54 AM	#5
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: putting a nv3500 in a 67-72 c-10 a shortshaft 350 driveshaft works on a shortbed if you change the front yoke. the Nv3500 is about the same size as a 350. I put it behind a pre 87 small block so I had to get the older style flywheel to make it work I suggest changing the clutch fork and the slave cylinder because these were week spots in the gm design. also make sure to use sycromesh in the tranny Ask what you will, I will try to get back to you guys in a timely fashion! Attached Images

07-04-2006, 11:05 AM	#6
Old Yeller 1970 DON'T TREAD ON ME Join Date: May 2005 Location: Crosby County, TX Posts: 989	Re: putting a nv3500 in a 67-72 c-10 Hey jamon8 glad to see the write up. Congrats on a job well done. __________________ Old Yeller

07-04-2006, 05:09 PM	#7
Brad Out of the carpool lane. Join Date: Jan 2000 Location: Clark Co, WA Posts: 5,672	Re: putting a nv3500 in a 67-72 c-10 Thanks for the write-up. I assume you did this with a V8? __________________ 1968 C-10 SWB, 5.7 Vortec/700R4/3.73 posi, Torch Red 1968 Camaro, 250/Powerglide, all original (No, I'm not gonna drop a 350 in it!...Jeez!) 2000 Honda VFR in the faster yellow! 2008 Husqvarna TE-610 1967 C-10 SWB 'Six Appeal'-Gone but not forgotten...

07-04-2006, 05:25 PM	#8
chevytrucks79 Registered User Join Date: Oct 2004 Location: Richmond, VA Posts: 68	Re: putting a nv3500 in a 67-72 c-10 Thanks for the report and the pictures. My crossmember is all the way to the front like it last had a smaller 3 speed in it. It looks to me I am going to have to take it back further, if it will even work. I will probally have to make or find one that will work.

07-04-2006, 11:49 PM	#9
chevybill Senior Member Join Date: Oct 2004 Location: calhoun city ms Posts: 940	Re: putting a nv3500 in a 67-72 c-10 I am using this tranny also. Do you have any pics of the pedal setup inside the truck? Did this tranny come out of a full size truck?(shifter location looks perfect) I have this tranny with a vortec 350 on tubular motor mounts in the v 8 position and I was able to use my stock driveshaft. My particular tranny came from a 4.3 s-10 so the shifter looks to sit further back than yours. Thanks so much for posting this. __________________ ongoing 1970 c 10 lwb 1994 z-28 few mods.-owned since new 1978 vette silver/grey 25th anniv. paint

07-05-2006, 09:48 PM	#10
chevybill Senior Member Join Date: Oct 2004 Location: calhoun city ms Posts: 940	Re: putting a nv3500 in a 67-72 c-10 Can you provide pics of the pedals mounted inside the cab? __________________ ongoing 1970 c 10 lwb 1994 z-28 few mods.-owned since new 1978 vette silver/grey 25th anniv. paint

07-06-2006, 08:10 AM	#11
jamon8 Registered User Join Date: Apr 2006 Location: southern Il Posts: 335	Re: putting a nv3500 in a 67-72 c-10 you guys will have to wait a while for that because I am in the process of painting the cab!

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.