|
|
|
10-18-2006, 03:03 AM
|
#1 |
|
Registered User
 
Join Date: Apr 2006
Location: San Diego
Posts: 147
|
Parts truck?
I have a chance at 500 dollars for a once rebuilt truck that has heavy front end damage. I need a cab for my 69 lwb because mine is toooo rusted. I need to know if since this is a 72 will the cabs swap out? will panels match? What will I have to do to make these two trucks have 1 solid body? I am really diggin this buy.
   
|
|
|
|
10-18-2006, 03:32 AM
|
#2 |
|
Registered User
Join Date: Apr 2006
Location: oklahoma
Posts: 10,669
|
Re: Parts truck?
The cab wiil swap no problem. But I would like to see some good pics of the driver side. Cause since she hit hard I wander if the cab has ben tweaked. Does the driver side door open and close easily? Do they still line up? If the cab is tweaked it is only good for basic parts. Like the dash, engine trans, rear axle. Just be real sure to look over what you want to use make sure it wasnt damaged.
Aaron |
|
|
|
|
10-18-2006, 08:42 AM
|
#3 |
|
Senior Member
Join Date: Nov 2005
Location: northwestern wi
Posts: 2,111
|
Re: Parts truck?
as aaron said check to be sure doors open and close properly. also look at seat back in realationship to rear window i have one that was hit and you can see the seat appears to be higher on one side than yhe other
__________________
common sense isn't so common anymore |
|
|
|
|
10-18-2006, 09:19 AM
|
#4 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,686
|
Re: Parts truck?
Is that a tilt column in there?
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
10-18-2006, 08:51 PM
|
#5 |
|
Senior Member
Join Date: Dec 2004
Location: Southern Pines NC
Posts: 3,853
|
Re: Parts truck?
I have seen trucks not hit as hard that have twisted cabs. The lower front corner of one was so bent they ended up using it for patches
|
|
|
|
|
10-18-2006, 10:14 PM
|
#6 |
|
Senior Member
Join Date: Nov 2005
Location: northwestern wi
Posts: 2,111
|
Re: Parts truck?
check out the floor and cab supports real close
__________________
common sense isn't so common anymore |
|
|
|
|
10-18-2006, 10:36 PM
|
#7 |
|
Senior Member
Join Date: Feb 2001
Location: Ridgecrest. CA, USA
Posts: 1,715
|
Re: Parts truck?
If the cab checks out and the it is also rust free all the way round, go for it. There is alot of guys in San Diego behind the seens looking for parts for these and you should be able to make some money back on some of the parts not used. The Truck swap is in Dec. and you can sell some unwanted parts there.
Good luck and I hope it is what you want and need!! Respectfully
__________________
Billy   1970 GMC Sierra Grande 402/TH400 (Longhorn)14 years and counting rebuild! 1975 (Build) Chevrolet SWB 4X4 350 SB Lifted 6 inches 1970 Ford F250 Ranger 390 BB 2010 Ford Super Duty F250 XLT W/4 inch lift kit and Pro Comp Tires Hub Cap Freak!    I need another truck like I need another hole in the head!I'M IN THE MARKET...AS IT WERE! |
|
|
|
|
10-19-2006, 04:40 AM
|
#8 |
|
Registered User
Join Date: Apr 2006
Location: San Diego
Posts: 147
|
Re: Parts truck?
That's what I'm thinking longhorn. However, I will probably end up just taking the front clip off of my truck and using it on this one because this one just is in better condition. I already told him I will take it. Yay
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
