Any interest in K20 misc frame pieces?

[masterbeavis]

Parting out a 71, have the frame left.(minus eng and trans cross member) I need to haul it off to the scrapyard here in a bit, was wondering if there was any interest in portions of the frame?

[msgross]

yep, can you help me out with this piece? Not sure if yours is the same but mine is a K-10 SWB..thanks... Here is the thread with my pics and issue... shipping would be to 17042 and I only need the small part.

http://67-72chevytrucks.com/vboard/s...d.php?t=218061

[masterbeavis]

These? They are not going to be fun to remove I will see what happens.

[1969k10stepside]

I need a motor mount/crossmember but since you are not selling it I will keep looking.I might need a piece no bigger than 4"X4" out of the very back crossmember from about the middle all the way up the 90 degree angle.I might still have a piece off a frame I scrapped but I might have already hauled it away.

[masterbeavis]

you will have to show me a picture of what you want, is it in one of MSGross' pics in the thread he linked? Right click, save as, load up in MSPaint, draw a circle on what part you need.

[1969k10stepside]

No,I dont have any pics on my computer right now but I can get a pic of what I need tomorrow.I might also need a set of brackets that are riveted to the frame which IIRC are for brake lines.You will probably just have to wait till I get some pics

[msgross]

I only need the driver side lower piece, let me check to be sure I don't need the pass side. You should be able to grind an "X" into the rivets and knick them off with an air chisel. If it's easier I can take the entire piece, up to you. Thanks...

[BobS]

Are the spring mounts available?

Bob

[masterbeavis]

BobS: yes, front or rear?
MSGross: it depends on how easy things come off. If it pisses me off bad enough, you might get part of the crossmember, and frame.

[msgross]

haha..

what about the frame piece that supports the power steering pump? I have seen threads where they welded that over my 68 frame to attach a newer PS box....

This is a borrowed pic of what I am talking about. He said he welded the outer piece onto the 67-68 frame. Mine doesn't have the dimple for the PS box.

[masterbeavis]

Uh, beats me, I have not removed the steering gear yet.

[msgross]

Originally Posted by masterbeavis

Uh, beats me, I have not removed the steering gear yet.

I take it that you plan on keeping the steering box, when you remove it I would like the area that it bolts to. Quick cut of the torch a few inches behind the back and in front of the front holes will do. let me know...thanks.

[4bynut]

Originally Posted by msgross

haha..

what about the frame piece that supports the power steering pump? I have seen threads where they welded that over my 68 frame to attach a newer PS box....

This is a borrowed pic of what I am talking about. He said he welded the outer piece onto the 67-68 frame. Mine doesn't have the dimple for the PS box.

Hey, that's the frame on my 67 (HA HA). Don't forget to put spacers in between the original frame and the frame section you weld on. Sorry i dont have pics of the piece before i welded it on to the original frame. I used big nuts that the gear box bolts would pass though. I welded them to the small frame section your putting over the original. I'll post a few more pics in the other thread. Thanks Jason

P.S. Masterbeavis, i need the box brackets if you part out the frame. I'll get pics tomorrow. Thanks Jason

[Rod]

I couldnt find anyone piecing out a frame earlier this year...now there coming out of the woodwork with the season changing. I dragged a stripped down chassis here, but I was missing the same engine and tranny cross members too.

[BobS]

Front/Fronts and Rear/Rears for the spring mounts.

Bob

[manimal]

is the frame totalled? or is it in good "builder" shape? I may be interested in the whole thing.Where is Eldorado at? I live in Cherry Valley,Ca(by SanBernardino)

[masterbeavis]

Manimal, if you want the entire frame, you can PM me, we can work out a price. Nothing is missing yet aside from the bracket for the clutch linkage. The frame will clean up and look like new, with no need for fixing rust holes.

[bad_turbo]

Eldorado is about 1 hour north of sacramento, off the 50 freeway, I believe.

[Blue_71]

if they're available id be interested (pending on price shipped to 42141) in the rear/front spring mounts.
to be specific, the four little metal straps, and the peice that mounts inside the frame for the bolt to go through. i cant remember if its bolted or rivited.

[masterbeavis]

ttt

[earl87gta]

put me in line for the front spring mounts.

[msgross]

any update on the parts?

[masterbeavis]

Yes, waiting on somebody to buy the entire frame. Probably isn't going to happen, have had a few people say "Dont cut it up, I want it" but they dont put their money where their mouth is.

[masterbeavis]

I am cutting it up today. Front spring hangars, and motor/trans cross members are gone

[BobS]

Can I get the rear spring hangers?

Bob