motor mount position - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Dean23 · 04-24-2002, 06:50 PM

What is the correct position for a v-8 in a 68 pickup. mine was sitting with the mounts right at the back of the x memeber. my trany has a short tailshaft on it as well. I'm probably going to get a x member and control arms out of a 79 pickup. How easy are they to swap in

------------------
Dean
edmonton,canada
68 c10, project in works,350, th350, plain jane.
SLOW AND STEADY GETS THE PANELS READY
http://communities.msn.ca/MyChevytruckpage

69 longhorn · 04-24-2002, 08:32 PM

Factory V8 smallblock has the stands bolted to the front of the crossmember(2wd). The stands are also different than the 6/250 stands. You can set the engine in on the 6/250 stands, for a little weight transfer,but the HEI dist will fit a little snug to the firewall,but will clear. I havent swapped a later crossmember,so cant really say on that one........69

Dean23 · 04-24-2002, 08:34 PM

the 283 that was in there was close to the fire wall. i couldn't pull the hei with the cap on, but with it off it would slide right out. Does anyone have a pic of which holes to use

------------------
Dean
edmonton,canada
68 c10, project in works,350, th350, plain jane.
SLOW AND STEADY GETS THE PANELS READY
http://communities.msn.ca/MyChevytruckpage

04-24-2002, 06:50 PM	#1
Dean23 68cst_ss490 Join Date: May 2001 Location: edmonton,canada Posts: 1,363	motor mount position What is the correct position for a v-8 in a 68 pickup. mine was sitting with the mounts right at the back of the x memeber. my trany has a short tailshaft on it as well. I'm probably going to get a x member and control arms out of a 79 pickup. How easy are they to swap in ------------------ Dean edmonton,canada 68 c10, project in works,350, th350, plain jane. SLOW AND STEADY GETS THE PANELS READY http://communities.msn.ca/MyChevytruckpage __________________ Dean edmonton,canada a winter wonderland 2005 Chevrolet Avalanche LT cold air intake, performance exhaust, Comp cams cam, jba shorty ceramic headers. http://www.cardomain.com/ride/3090973

04-24-2002, 08:32 PM	#2
69 longhorn Registered User Join Date: Aug 2001 Location: rock island,il,usa Posts: 5,382	Factory V8 smallblock has the stands bolted to the front of the crossmember(2wd). The stands are also different than the 6/250 stands. You can set the engine in on the 6/250 stands, for a little weight transfer,but the HEI dist will fit a little snug to the firewall,but will clear. I havent swapped a later crossmember,so cant really say on that one........69 __________________ http://community.webshots.com/user/hotrodhorn

04-24-2002, 08:34 PM	#3
Dean23 68cst_ss490 Join Date: May 2001 Location: edmonton,canada Posts: 1,363	the 283 that was in there was close to the fire wall. i couldn't pull the hei with the cap on, but with it off it would slide right out. Does anyone have a pic of which holes to use ------------------ Dean edmonton,canada 68 c10, project in works,350, th350, plain jane. SLOW AND STEADY GETS THE PANELS READY http://communities.msn.ca/MyChevytruckpage __________________ Dean edmonton,canada a winter wonderland 2005 Chevrolet Avalanche LT cold air intake, performance exhaust, Comp cams cam, jba shorty ceramic headers. http://www.cardomain.com/ride/3090973

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.