WTB crossmember piece, cab mounts for 4WD - The 1947 - Present Chevrolet & GMC Truck Message Board Network

msgross · 04-05-2007, 11:20 PM

I need these ASAP. Also need both rear cab mounts. Shipping to 17042 or Carlisle swap meet in two weeks in Central PA. Thanks...

don't need crossmember anymore, still need cab mounts...PLEASE HELP!

1969k10stepside · 04-05-2007, 11:23 PM

Mike,thats the piece that was rusted out on mine causing all the frame problems....I fixed mine but it wasnt near that bad.For a cheap fix you could get some metal and weld up a new peice for that crossmember.TTT for ya.I *think* that the crossmember for a 4x4 (long or shortbed) is slightly different than the ones on 2wds but I cant remember.

msgross · 04-05-2007, 11:33 PM

actually that side of the frame was fine, the other side had this small hole. I think that i'll graft in a small piece of steel to replace this part. I have also noticed some other crossmember that I need to remove to clean out rot before they get worse.

1969k10stepside · 04-05-2007, 11:39 PM

That pic reminds me of my frame troubles.....Looks like it needs the same treatment mine required.A sawz-all to cut the old out and a new piece to put in,and a welder to put it all together.It looks like it fairly thin for a few inches around that hole.If you need any 4x4 crossmembers( t case x member,ect),I have atleast one of them.

qksilver · 04-05-2007, 11:43 PM

I know I have the frame mounts, just stripped another truck. As far as the crossmember I have one from a 2 wheel drive leaf spring truck. I will be out at the shop Sat and will match it up to my swb 4x4 to see if they are the same or will swap.
Thanks,
Steve

msgross · 04-05-2007, 11:45 PM

Thanks Steve, let me know what you have...

qksilver · 04-05-2007, 11:54 PM

ok

msgross · 04-06-2007, 09:19 AM

troy-built is working on the parts too so first one with pics and good price gets the dough... thanks

If it's easier then I might take the entire crossmember (16 rivets) vs the lower piece (8 rivets).

**t korinek** · 04-07-2007, 02:44 PM

I have a crossmember in good shape if the others fall through. $55 shipped.
Thanks, Tom

msgross · 04-07-2007, 04:27 PM

how much for just the lower driver side piece that is rusted on mine? 17042 for shipping...thanks

msgross · 04-08-2007, 10:12 PM

ttt still looking

msgross · 04-09-2007, 09:03 PM

ttt still looking for parts...thanks

msgross · 04-10-2007, 08:45 AM

PM sent Tom...

msgross · 04-10-2007, 10:55 PM

Tom payment sent for full crossmember, Steve, will send payment tomorrow upon pics. Thanks guys,

msgross · 04-12-2007, 06:44 PM

still need cab mounts... qksilver, did you get yours yet?

msgross · 04-13-2007, 11:13 PM

ttt cab mounts still needed

neo1370 · 04-13-2007, 11:18 PM

pulling a cab this weekend,I'll let you know if mounts are any good

**t korinek** · 04-14-2007, 02:26 AM

I'll check on cab mounts too. Tom

msgross · 04-14-2007, 07:11 AM

thanks

72swbcamo · 04-14-2007, 12:48 PM

I have a brand new set of polyethlene mounts for 4x4 if your interested. Could knock a few dollars what I paid for them.

msgross · 04-14-2007, 01:39 PM

I already have the rubber mounts, need the metal parts for the frame.. I assume that you have the rubber/urethane part? Thanks though

04-05-2007, 11:20 PM	#1
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	WTB crossmember piece, cab mounts for 4WD I need these ASAP. Also need both rear cab mounts. Shipping to 17042 or Carlisle swap meet in two weeks in Central PA. Thanks... don't need crossmember anymore, still need cab mounts...PLEASE HELP! Attached Images __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer" Last edited by msgross; 04-13-2007 at 11:14 PM.

04-05-2007, 11:23 PM	#2
1969k10stepside Registered User Join Date: Mar 2006 Location: USA Posts: 21,020	Re: WTB crossmember piece, cab mounts for 4WD Mike,thats the piece that was rusted out on mine causing all the frame problems....I fixed mine but it wasnt near that bad.For a cheap fix you could get some metal and weld up a new peice for that crossmember.TTT for ya.I think that the crossmember for a 4x4 (long or shortbed) is slightly different than the ones on 2wds but I cant remember.

04-05-2007, 11:33 PM	#3
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD actually that side of the frame was fine, the other side had this small hole. I think that i'll graft in a small piece of steel to replace this part. I have also noticed some other crossmember that I need to remove to clean out rot before they get worse. Attached Images __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-05-2007, 11:39 PM	#4
1969k10stepside Registered User Join Date: Mar 2006 Location: USA Posts: 21,020	Re: WTB crossmember piece, cab mounts for 4WD That pic reminds me of my frame troubles.....Looks like it needs the same treatment mine required.A sawz-all to cut the old out and a new piece to put in,and a welder to put it all together.It looks like it fairly thin for a few inches around that hole.If you need any 4x4 crossmembers( t case x member,ect),I have atleast one of them. Last edited by 1969k10stepside; 04-05-2007 at 11:40 PM.

04-05-2007, 11:43 PM	#5
qksilver Senior Member Join Date: Dec 2004 Location: Southern Pines NC Posts: 3,853	Re: WTB crossmember piece, cab mounts for 4WD I know I have the frame mounts, just stripped another truck. As far as the crossmember I have one from a 2 wheel drive leaf spring truck. I will be out at the shop Sat and will match it up to my swb 4x4 to see if they are the same or will swap. Thanks, Steve

04-05-2007, 11:45 PM	#6
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD Thanks Steve, let me know what you have... __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-05-2007, 11:54 PM	#7
qksilver Senior Member Join Date: Dec 2004 Location: Southern Pines NC Posts: 3,853	Re: WTB crossmember piece, cab mounts for 4WD ok

04-06-2007, 09:19 AM	#8
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD troy-built is working on the parts too so first one with pics and good price gets the dough... thanks If it's easier then I might take the entire crossmember (16 rivets) vs the lower piece (8 rivets). __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-07-2007, 02:44 PM	#9
t korinek Truckin' Krazy Join Date: May 2000 Location: mesa az Posts: 6,193	Re: WTB crossmember piece, cab mounts for 4WD I have a crossmember in good shape if the others fall through. $55 shipped. Thanks, Tom Attached Images __________________ Dealer for: American Auto Wire Precision weatherstripping Dakota Digital Trim parts Carpets Truck World seat covers & Many others Chevy Parts locator in Mesa AZ!

04-07-2007, 04:27 PM	#10
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD how much for just the lower driver side piece that is rusted on mine? 17042 for shipping...thanks __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer" Last edited by msgross; 04-07-2007 at 04:28 PM.

04-08-2007, 10:12 PM	#11
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD ttt still looking __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-09-2007, 09:03 PM	#12
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD ttt still looking for parts...thanks __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-10-2007, 08:45 AM	#13
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD PM sent Tom... __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-10-2007, 10:55 PM	#14
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD Tom payment sent for full crossmember, Steve, will send payment tomorrow upon pics. Thanks guys, __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-12-2007, 06:44 PM	#15
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD still need cab mounts... qksilver, did you get yours yet? __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"



Register or Log In To remove these advertisements.

04-13-2007, 11:13 PM	#16
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD ttt cab mounts still needed __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-13-2007, 11:18 PM	#17
neo1370 Registered User Join Date: Aug 2006 Location: PA Posts: 241	Re: WTB crossmember piece, cab mounts for 4WD pulling a cab this weekend,I'll let you know if mounts are any good

04-14-2007, 02:26 AM	#18
t korinek Truckin' Krazy Join Date: May 2000 Location: mesa az Posts: 6,193	Re: WTB crossmember piece, cab mounts for 4WD I'll check on cab mounts too. Tom __________________ Dealer for: American Auto Wire Precision weatherstripping Dakota Digital Trim parts Carpets Truck World seat covers & Many others Chevy Parts locator in Mesa AZ!

04-14-2007, 07:11 AM	#19
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD thanks __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

04-14-2007, 12:48 PM	#20
72swbcamo Active Member Join Date: Dec 2003 Location: Waterbury, CT Posts: 591	Re: WTB crossmember piece, cab mounts for 4WD I have a brand new set of polyethlene mounts for 4x4 if your interested. Could knock a few dollars what I paid for them. Last edited by 72swbcamo; 04-14-2007 at 12:49 PM.

04-14-2007, 01:39 PM	#21
msgross Registered User Join Date: Jul 2006 Location: Central PA Posts: 12,201	Re: WTB crossmember piece, cab mounts for 4WD I already have the rubber mounts, need the metal parts for the frame.. I assume that you have the rubber/urethane part? Thanks though __________________ The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer"

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.