ok shoot this idea down - The 1947 - Present Chevrolet & GMC Truck Message Board Network

satin64 · 08-28-2007, 09:26 PM

is their a leaf spring setup with the axle on top that will bolt in or with minor modification fit under a 64 swb?

**ChiefRocka** · 08-28-2007, 10:17 PM

Didn't we go thru this already ??

PrerunnerRob · 08-28-2007, 11:04 PM

Is this for a leaf sprung truck already or a truck with trailing arms?

satin64 · 08-29-2007, 02:35 AM

i did ask but didn't get an answer to this specific question.i was hoping someone did a complete swap from a donor.i know i could lose a few leafs and gain a few inches but at what cost to load capacity?i was hoping there was a station wagon or land yacht i could steal from.i'm getting the front disc parts back this week i hope and was looking to do the rear drop at the same time.

i also noticed allot of old posts don't get looked at that much,at least it seems that way.i guess i could have just posted in the old thread

Tim64 · 08-29-2007, 07:43 AM

Can I ask why you want to go to leaf springs? Sounds like a lot of work to me. IMHO
Tim

Stepside65 · 08-29-2007, 07:48 AM

Almost all of 63 and up GMC's have leaf springs. Shouldn't be too hard to convert.

satin64 · 08-29-2007, 11:11 AM

convert to trailing arms?is it a bolt in deal?

jchav62 · 08-29-2007, 01:59 PM

Your truck has leaf springs? Did it start life as a GMC?

Frizzle Fry · 08-29-2007, 03:57 PM

If you already have leaves can't you just throw a flip kit on there?

**Captainfab** · 08-29-2007, 04:15 PM

Quote:

Originally Posted by Frizzle Fry

If you already have leaves can't you just throw a flip kit on there?

X2....one issue you might have though is that your springs are most likely 2 1/4" wide, and the newer (73 & up) springs are 2 1/2" wide. A flip kit for the
'73 and newer may work, but I just thought I'd mention about the springs....something to check.

PrerunnerRob · 08-29-2007, 11:48 PM

Let me ask this...what is the desired end result from the work you want to do?

satin64 · 08-30-2007, 05:02 AM

i want a hard drop as low as possible with a decent ride and some load capacity.its a gmc with leafs.i have been thinking of a c notch, and i have some flip kit parts off a 2000 silverado,(but im not sure they will work).then cutting the coils up front when i add the 78 disc front end.i was hoping there was a bolt in axle over leaf donor vehicle out there,but i guess not.i dont have a big welder,just a gas less 110v.im doing this all in my drive way so i need all my ducks in a row to get it dropped in one weekend.

08-28-2007, 09:26 PM	#1
satin64 Registered User Join Date: Aug 2007 Location: st.helens oregon Posts: 312	ok shoot this idea down is their a leaf spring setup with the axle on top that will bolt in or with minor modification fit under a 64 swb?

08-28-2007, 10:17 PM	#2
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: ok shoot this idea down Didn't we go thru this already ?? __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

08-28-2007, 11:04 PM	#3
PrerunnerRob Registered User Join Date: Jan 2007 Location: San Jose Posts: 847	Re: ok shoot this idea down Is this for a leaf sprung truck already or a truck with trailing arms?

08-29-2007, 02:35 AM	#4
satin64 Registered User Join Date: Aug 2007 Location: st.helens oregon Posts: 312	Re: ok shoot this idea down i did ask but didn't get an answer to this specific question.i was hoping someone did a complete swap from a donor.i know i could lose a few leafs and gain a few inches but at what cost to load capacity?i was hoping there was a station wagon or land yacht i could steal from.i'm getting the front disc parts back this week i hope and was looking to do the rear drop at the same time. i also noticed allot of old posts don't get looked at that much,at least it seems that way.i guess i could have just posted in the old thread Last edited by satin64; 08-29-2007 at 02:35 AM.

08-29-2007, 07:43 AM	#5
Tim64 Registered User Join Date: Aug 2007 Location: Vandalia, Ohio Posts: 396	Re: ok shoot this idea down Can I ask why you want to go to leaf springs? Sounds like a lot of work to me. IMHO Tim

08-29-2007, 07:48 AM	#6
Stepside65 Still Truckless! Join Date: Jul 2007 Location: Valrico, Florida Posts: 3,166	Re: ok shoot this idea down Almost all of 63 and up GMC's have leaf springs. Shouldn't be too hard to convert. __________________ ~James Truckless 2009 Hyundai Sonata<~~Wife's sedanomatic 1997 Nissan Pickup Father-in-law's tonka toy I am forced to drive Founder of The 60-66 Club Tutor Et Ultor

08-29-2007, 11:11 AM	#7
satin64 Registered User Join Date: Aug 2007 Location: st.helens oregon Posts: 312	Re: ok shoot this idea down convert to trailing arms?is it a bolt in deal?

08-29-2007, 01:59 PM	#8
jchav62 1962 C-10 Join Date: Apr 2005 Location: Las Vegas, New Mexico Posts: 4,978	Re: ok shoot this idea down Your truck has leaf springs? Did it start life as a GMC? __________________ Joseph Chavez "See the USA in a Chevrolet!!" ......................_____ .........________//__{\_____ ,,,,,,,/__(O)___//___/__(O)_/ 1962 C10 Shortbed Fleetside 327/th350 GV overdrive 1974 C10 Longbed Fleetside 350/th350 "The Trash Truck" 1999 Chevy 2500 OBS, Longbed 5.7/4L80E 4x4 2015 GMC Sierra SLE 1500 4x4

08-29-2007, 03:57 PM	#9
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: ok shoot this idea down If you already have leaves can't you just throw a flip kit on there?

08-29-2007, 11:48 PM	#11
PrerunnerRob Registered User Join Date: Jan 2007 Location: San Jose Posts: 847	Re: ok shoot this idea down Let me ask this...what is the desired end result from the work you want to do?

08-30-2007, 05:02 AM	#12
satin64 Registered User Join Date: Aug 2007 Location: st.helens oregon Posts: 312	Re: ok shoot this idea down i want a hard drop as low as possible with a decent ride and some load capacity.its a gmc with leafs.i have been thinking of a c notch, and i have some flip kit parts off a 2000 silverado,(but im not sure they will work).then cutting the coils up front when i add the 78 disc front end.i was hoping there was a bolt in axle over leaf donor vehicle out there,but i guess not.i dont have a big welder,just a gas less 110v.im doing this all in my drive way so i need all my ducks in a row to get it dropped in one weekend. Last edited by satin64; 08-30-2007 at 05:03 AM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.