need help with block ID - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jcblue · 11-07-2007, 05:49 PM

i need some help ID ind teh block in my truck
teh pad in front of the head reads: 1mo527 6vp
the casting numbers are 10066036..
i was having trouble reading teh casting some of teh sixes may have been eights
i do know its from an 80s truck cause the dip stick is on the pass side
thanks
josh

jcblue · 11-07-2007, 10:08 PM

anyone

**too much stuff** · 11-07-2007, 10:50 PM

The casting numbers don't jive in my book...

Kool K5 · 11-07-2007, 10:51 PM

Well heres the site I use to decode engine blocks, but I don't see anything like that.

http://www.nastyz28.com/sbchevy/sblock.html

Evan

syncrov69 · 11-08-2007, 06:00 AM

10066036 350 86-up 205HP Car & Truck 2 & 4-bolt Passenger stick 1-piece seal

ABLAZN · 11-08-2007, 07:36 AM

I came up with it as a crate motor. It should have a 2 piece rear seal if that is that case. Here is the information that I found for the number in front of the right head.

Target Master/Goodwrench crate motors will have a serial number something like "1M1234VB" or "1MO1234VP" or even "2M1234VB" or something along those lines. It is only a serial number. There is no way to decode the horsepower of the engine.

The casting number shows as:
10066036 350 2/4(bolt) Target Master/Goodwrench crate motor, 2-piece rear seal, "Hecho en Mexico"

Here is a link to the site that I found it on. It is the best one that I have found so far. You have to dig through it quite a bit at times, but most of the codes can be found if you look for a while.
LINK

jcblue · 11-08-2007, 10:52 PM

thanks yall i appreciate it

11-07-2007, 05:49 PM	#1
jcblue Registered User Join Date: Aug 2007 Location: Elkton, ky Posts: 385	need help with block ID i need some help ID ind teh block in my truck teh pad in front of the head reads: 1mo527 6vp the casting numbers are 10066036.. i was having trouble reading teh casting some of teh sixes may have been eights i do know its from an 80s truck cause the dip stick is on the pass side thanks josh

11-07-2007, 10:08 PM	#2
jcblue Registered User Join Date: Aug 2007 Location: Elkton, ky Posts: 385	Re: need help with block ID anyone

11-07-2007, 10:50 PM	#3
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,717	Re: need help with block ID The casting numbers don't jive in my book... __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

11-07-2007, 10:51 PM	#4
Kool K5 Registered User Join Date: Sep 2006 Location: Niverville, Mb Posts: 88	Re: need help with block ID Well heres the site I use to decode engine blocks, but I don't see anything like that. http://www.nastyz28.com/sbchevy/sblock.html Evan __________________ 70 Blazer 4x4 305/sm465/np205 80 Buick LeSabre Limited 72 Honda CB350F 77 Honda Cb750K 00 Ducati Monster M900ie

11-08-2007, 06:00 AM	#5
syncrov69 Registered User Join Date: Aug 2007 Location: Laval, Québec, Canada Posts: 175	Re: need help with block ID 10066036 350 86-up 205HP Car & Truck 2 & 4-bolt Passenger stick 1-piece seal __________________ '71 Custom/10 Deluxe LWB '71 Custom/30 Deluxe Dually

11-08-2007, 07:36 AM	#6
ABLAZN Oh..never mind.... Join Date: Aug 2006 Location: Oregon Posts: 588	Re: need help with block ID I came up with it as a crate motor. It should have a 2 piece rear seal if that is that case. Here is the information that I found for the number in front of the right head. Target Master/Goodwrench crate motors will have a serial number something like "1M1234VB" or "1MO1234VP" or even "2M1234VB" or something along those lines. It is only a serial number. There is no way to decode the horsepower of the engine. The casting number shows as: 10066036 350 2/4(bolt) Target Master/Goodwrench crate motor, 2-piece rear seal, "Hecho en Mexico" Here is a link to the site that I found it on. It is the best one that I have found so far. You have to dig through it quite a bit at times, but most of the codes can be found if you look for a while. LINK __________________ 1972 Blazer -6 inch lift -35 inch BFG A/T's Turbo 350 NP-205 454 BB (for now) MORE TO COME !!!!!! Now going to 2WD!!!!! Sold. I got it back after 22 years and did not even know it !!! THE STORY HERE Project Low Down Dirty Rat Last edited by ABLAZN; 11-08-2007 at 07:37 AM.

11-08-2007, 10:52 PM	#7
jcblue Registered User Join Date: Aug 2007 Location: Elkton, ky Posts: 385	Re: need help with block ID thanks yall i appreciate it

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.