|
|
|
01-22-2008, 07:42 AM
|
#1 |
|
Registered User
Join Date: Oct 2007
Location: San Antonio TX
Posts: 124
|
Need some info
I pulled my seats today getting ready to take the to get redone. What I found was conduit brackets holding the fron of my rear seat down ...I know that isn't right but what should be there?? Also when I pulled the drivers side bucket out it doesn't have anything connecting the left side to the right and isn't adjustable what should it look like? I will try and post a picture later
|
|
|
|
01-22-2008, 07:47 AM
|
#2 |
|
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
Re: Need some info
The front of the rear seat is held down from the factory with what appear to be heavy duty conduit brackets. There are a lot of pictures of them on the board.
Here's a thread with a good picture. http://67-72chevytrucks.com/vboard/s...ht=blazer+hold
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. Last edited by 71swb4x4; 01-22-2008 at 07:49 AM. |
|
|
|
|
01-22-2008, 08:18 AM
|
#3 |
|
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,482
|
Re: Need some info
Yeppers, they can be had on Evil Bay and Here from time to time.
They are NOT reproduced at this time and run about $50-$100 
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
|
|
|
01-22-2008, 12:21 PM
|
#4 |
|
Registered User
Join Date: May 2007
Location: San Antonio
Posts: 993
|
Re: Need some info
Hey Hoss, I just pulled my factory buckets out Saturday in favor of some seats out of a 2004 Tahoe. I'll try to post some pics of the drivers seat tomorrow. BTW, what side of town are you on? Does your rig have superlift springs. How does it ride? Anyways, let me know.
|
|
|
|
|
01-22-2008, 12:39 PM
|
#5 |
|
Registered User
Join Date: Oct 2007
Location: San Antonio TX
Posts: 124
|
Re: Need some info
I live in Northern Hills off of Nacadoshes (sp) , I'm not sure what lift I have but it rides rough but I'm sure the Mud TA's don't help much. I'm having me seats redone so I should be on the road in a week or two. That will give me the oppertunity to do some stuff inside I want.
|
|
|
|
|
01-22-2008, 01:47 PM
|
#6 |
|
Registered User
Join Date: May 2007
Location: San Antonio
Posts: 993
|
Re: Need some info
I'm off of 410 and Ingram. I'm in the process of doing an engine swap. I've been buying a lot of parts for it lately. I hope to get it running soon. I need to buy a cherry picker to finish the motor swap. Hopefully by the end of Feb. it will be on the street. Mario.
|
|
|
|
|
01-23-2008, 10:41 AM
|
#7 |
|
Registered User
Join Date: Oct 2007
Location: San Antonio TX
Posts: 124
|
Re: Need some info
Here is pictures of the under side of my drivers seat what is missing? and can I get it ? I know the left side of the seat should have something like the rightside ? Any help would be appreciated.
|
|
|
|
|
01-23-2008, 10:48 AM
|
#8 |
|
Registered User
Join Date: Oct 2007
Location: San Antonio TX
Posts: 124
|
Re: Need some info
Mario how is your project going? I took my seats to the upholster tonight .
|
|
|
|
|
01-23-2008, 10:23 PM
|
#9 |
|
Senior Member
Join Date: Jun 2001
Location: Shelbyville, KY
Posts: 3,269
|
Re: Need some info
You are missing the heavy wire that runs from the left side release to the right side release so that when you pull that lever, you also pull the locking pin on the other side. Works exactly like a regular bench seat.
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
