WTB, used printed circuit for a Tach dash - The 1947 - Present Chevrolet & GMC Truck Message Board Network

JimKshortstep4x4 · 03-19-2008, 04:18 PM

I need a good used printed circuit for a tach dash. Please post a picture and include shipping with price. Shipping is to 49445.

Thanks,

Jim

68Mike · 03-19-2008, 08:19 PM

I've seen these on ebay for like $20 bucks. Never tried one one but they list they are new

myoldchevytruck · 03-19-2008, 08:40 PM

Jim, Here's one I posted last week. I have a 7 gauge Printed Circuit Board (PCB) $15 plus $8.95 shipping to 49445.

Tell me if you want it.

JimKshortstep4x4 · 03-19-2008, 10:08 PM

myoldchevy truck,

The printed circuit in your picture is for a dash that does not have a tach in it. The tach dash printed circuit has a "hole" in the middle to clear the tach. I cannot use the printed circuit pictured.

Thanks for the reply, though.

68mike,

Thanks for the info. I will check it out.

Jim

myoldchevytruck · 03-19-2008, 10:16 PM

Jim sorry about that.

**Classic Bowties** · 03-20-2008, 02:52 AM

Here is a pic of the type printed circuit that he is looking to buy. Cb

GMC Jim · 03-20-2008, 01:23 PM

When I installed a marine tach several years ago; I cut the printed circuit in the center. Then scraped each end of the 10 inlaid wire traces. This enabled inserting and soldering suitable wire lenghts between the cut traces...was not that hard to do......... Jim

JimKshortstep4x4 · 03-20-2008, 01:37 PM

teeitup,

That is what I found, also.

GMC Jim,

I had made up a printed circuit like you described but I was hoping not to have to use it. If I cannot get a good used printed circuit I will use the one that I had made up.

Jim

03-19-2008, 04:18 PM	#1
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	WTB, used printed circuit for a Tach dash I need a good used printed circuit for a tach dash. Please post a picture and include shipping with price. Shipping is to 49445. Thanks, Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

03-19-2008, 08:19 PM	#2
68Mike Registered User Join Date: Jan 2007 Location: Salinas,Ca 93906 Posts: 502	Re: WTB, used printed circuit for a Tach dash I've seen these on ebay for like $20 bucks. Never tried one one but they list they are new __________________ Mike Currents: '74 Cheyenne Super C30 Camper Special 3+3 aka "Sucia30" Past: '79 C10 BIG 10 (Sold) 69 CST LWB - Always a "Work in progress" true work truck (stolen) 05 GSXR 750 it has a pretty paint job _wrecked 72 SWB full frame restoration -sold! 71 CST K5 Blazer 4x4 (soon to be 2wd)-project - sold! C10 Club 2012 Brothers Show Video http://youtu.be/pUeV2vP7Wpo

03-19-2008, 08:40 PM	#3
myoldchevytruck Retired Air Force Veteran Join Date: Aug 2007 Location: Pembroke Pines, Florida 33024 Posts: 1,808	Re: WTB, used printed circuit for a Tach dash Jim, Here's one I posted last week. I have a 7 gauge Printed Circuit Board (PCB) $15 plus $8.95 shipping to 49445. Tell me if you want it. __________________ Harry 69' SWB Step Side 1/2 Ton w/68' Front Clip Swap from Leafs to Trailing Arms (Complete) Swap 6 Lug to 5 Lug (w/ Disk Brakes in Front) 3/6 Drop Help Support The Board Click Here For Information On How To Subscribe Krue's FAQ Page Vendors Last edited by myoldchevytruck; 03-19-2008 at 10:22 PM. Reason: recalculate postage

03-19-2008, 10:08 PM	#4
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: WTB, used printed circuit for a Tach dash myoldchevy truck, The printed circuit in your picture is for a dash that does not have a tach in it. The tach dash printed circuit has a "hole" in the middle to clear the tach. I cannot use the printed circuit pictured. Thanks for the reply, though. 68mike, Thanks for the info. I will check it out. Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

03-19-2008, 10:16 PM	#5
myoldchevytruck Retired Air Force Veteran Join Date: Aug 2007 Location: Pembroke Pines, Florida 33024 Posts: 1,808	Re: WTB, used printed circuit for a Tach dash Jim sorry about that. __________________ Harry 69' SWB Step Side 1/2 Ton w/68' Front Clip Swap from Leafs to Trailing Arms (Complete) Swap 6 Lug to 5 Lug (w/ Disk Brakes in Front) 3/6 Drop Help Support The Board Click Here For Information On How To Subscribe Krue's FAQ Page Vendors

03-20-2008, 02:52 AM	#6
Classic Bowties Always on the hunt... Join Date: Sep 2006 Location: Portland, OR. Posts: 5,747	Re: WTB, used printed circuit for a Tach dash Here is a pic of the type printed circuit that he is looking to buy. Cb Attached Images

03-20-2008, 01:23 PM	#7
GMC Jim Senior Member Join Date: Dec 2002 Location: Portland, Oregon Posts: 901	Re: WTB, used printed circuit for a Tach dash When I installed a marine tach several years ago; I cut the printed circuit in the center. Then scraped each end of the 10 inlaid wire traces. This enabled inserting and soldering suitable wire lenghts between the cut traces...was not that hard to do......... Jim Attached Images __________________ '71 GMC;fleetside;PB/PS/AC/CC/402 Eng./Custom Paint/110,000act miles/3 fuel tanks(52gal). Last edited by GMC Jim; 03-20-2008 at 01:29 PM.

03-20-2008, 01:37 PM	#8
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: WTB, used printed circuit for a Tach dash teeitup, That is what I found, also. GMC Jim, I had made up a printed circuit like you described but I was hoping not to have to use it. If I cannot get a good used printed circuit I will use the one that I had made up. Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.