Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
04-03-2008, 08:40 AM | #1 |
Registered User
Join Date: Oct 2006
Location: las vegas
Posts: 88
|
rusty bolts- need help
I am currenly in the dissassembly stage of my bed and have two new bedsides ret to go. I got the tailgate off and the front panel unbolted with no issues, however, the bolts that are in the inside "angle" are small cariage bolts and after a few turns, the bolt and the nut turn together and make no progress. So, does any one have any tips on how I get get these things off quick like? I wont be re-using them so the more destructive the better, Thanx.
__________________
69 shorty w/ 67 front clip |
04-03-2008, 08:43 AM | #2 |
Tasty Cakes!
Join Date: Apr 2003
Location: Gilbert, AZ
Posts: 2,112
|
Re: rusty bolts- need help
Use an angle grinder? Or drill out the bolt heads? Hacksaw? Torch?
__________________
I'm a little and a lot Ground beef: A cow with no legs. ---------------- '66 Chevy SWB "Penny" '67 Chevy Big Window SWB- aka "Pearl" '72 Burb- "Betty" "It's not a hearse dammit" '99 Chevy Ext. cab Silverado |
04-03-2008, 08:43 AM | #3 |
Cantankerous Geezer
Join Date: Aug 2002
Location: Bel Aire, KS
Posts: 6,264
|
Re: rusty bolts- need help
If you have a welder you can weld a nut on the bolt head.
__________________
Fred There is no such thing as too much cam...just not enough engine. |
04-03-2008, 08:44 AM | #4 |
Senior Member
Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,237
|
Re: rusty bolts- need help
pb blaster is your friend
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
04-03-2008, 08:49 AM | #5 |
Registered User
Join Date: Oct 2006
Location: las vegas
Posts: 88
|
Re: rusty bolts- need help
wow! thanx for the feedback guys!! I was thinking about a torch and a air chisel, but some of your suggestions may be a little more do-able.
__________________
69 shorty w/ 67 front clip |
04-03-2008, 09:26 AM | #6 |
Registered User
Join Date: Dec 2007
Location: Nanaimo B.C.
Posts: 604
|
Re: rusty bolts- need help
you may be able to tighten the up and keep tighting them till they bust off. I do this all the time to get rust bolts off on these boxes
__________________
I was hooked on these trucks since 1982 when I drove my budys fathers 1968 Custum GMC 396 automatic dana 60 rear with a power lock diff what a ride more fun then we will we can ever tell!! |
04-03-2008, 09:59 AM | #7 |
BlahBlahBlah
Join Date: Feb 2002
Location: Wa.
Posts: 20,021
|
Re: rusty bolts- need help
On small bolts like that if you can get a vice grips on em, nose grip not a side grip, sometimes you can just rock em back and forth and they will break off.
Too bad both sides are spinning. The tighten em till they break is another good way, as suggested already. |
04-03-2008, 12:43 PM | #8 |
Registered User
Join Date: Dec 2004
Location: Central Wisconsin
Posts: 1,317
|
Re: rusty bolts- need help
Just tighten them about 1/2 turn-they will break-----easy to do.
|
04-03-2008, 02:24 PM | #9 |
Senior Member
Join Date: Feb 2001
Location: Killen, Alabama USA
Posts: 3,625
|
Re: rusty bolts- need help
2 words - oxygen, acetylene. Whenever I pull a bed or take one apart, I go ahead and get my torch rig out. I usually cut the nuts off without even trying to wrench them off - especially wood beds!!
Joshua
__________________
72 Cheyenne Super swb. Factory 402/400,tach,posi,AM/FM, A/C. Adding cruise, 8-track 72 Cheyenne Super swb. 350/350 A/C, bucket seats 72 Cheyenne swb. Factory 402/400, tilt, posi, A/C 72 Cheyenne Super K-10. 350/4 spd., posi. 72 Suburban 350/350 tilt, tach, AM/FM, A/C, luggage rack 72 GMC Sierra lwb. 350/350, A/C. medium green/olive interior |
04-04-2008, 07:48 AM | #10 |
huh ???
Join Date: Nov 2002
Location: Fredericksburg,Va.
Posts: 3,368
|
Re: rusty bolts- need help
I took a small grinder and cut a slot so a friend could hold them with a big flat screw driver...
Chuck
__________________
90 Blazer Silverado 350w/ 700R4 and 32" Kelly's "I am a bomb technician. If you see me running try to keep up!" |
04-04-2008, 07:56 AM | #11 |
Registered User
Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: rusty bolts- need help
__________________
69 C10 LWB GM 350 crate motor, 3.73 rearend |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|