np205 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

orangeblossomspecial · 11-10-2008, 10:57 PM

Hello!

I'm looking for the specs on the bolt/stud that the 4x4 floor shifter pivots on that is attached to the adapter that connects the np205 with the manual transmission. 1972 chevy 3/4 ton. If anyone knows where I can get one great, otherwise I will mfg one

Many Thanks

eric67m · 11-11-2008, 01:58 AM

I have two currently in my garage with the two shifters that go with them (I dont know which I am going to use yet, both from sm465/np205's as far as I know). I dont know where you could buy one, possibly someone on the board here has an extra one.

The one on the top is for an older style adapter, I believe, it uses a 7/16 - 14tpi 2 1/2" long bolt (with a few washers)

The one on the bottom is I assume a newer style, 9/16 - 11 tpi 2 5/16" overall long. It has a 3/4 x 1 1/2 shoulder with a 1/2 x1/16 groove for grease. This set up seems to have a lot of sideways slop in the shifter, I may need to drill out and add a bushing to the lever.

I hope this helps some.

Ace in the hole · 11-11-2008, 09:25 AM

I got one from manes- it's under "motor, cab & misc. mounts"
http://www.manestruckparts.com/store...Category_ID=16
Also found this old thread- http://67-72chevytrucks.com/vboard/s...t=shifter+bolt

orangeblossomspecial · 11-11-2008, 10:36 AM

Many Thanks again,

Appreciate the pictures and found what I needed at Manes

11-10-2008, 10:57 PM	#1
orangeblossomspecial Registered User Join Date: Sep 2008 Location: Rexburg, Idaho Posts: 34	np205 Hello! I'm looking for the specs on the bolt/stud that the 4x4 floor shifter pivots on that is attached to the adapter that connects the np205 with the manual transmission. 1972 chevy 3/4 ton. If anyone knows where I can get one great, otherwise I will mfg one Many Thanks Last edited by orangeblossomspecial; 11-10-2008 at 11:05 PM.

11-11-2008, 01:58 AM	#2
eric67m Registered User Join Date: Apr 2005 Location: Monroe, WA Posts: 298	Re: np205 I have two currently in my garage with the two shifters that go with them (I dont know which I am going to use yet, both from sm465/np205's as far as I know). I dont know where you could buy one, possibly someone on the board here has an extra one. The one on the top is for an older style adapter, I believe, it uses a 7/16 - 14tpi 2 1/2" long bolt (with a few washers) The one on the bottom is I assume a newer style, 9/16 - 11 tpi 2 5/16" overall long. It has a 3/4 x 1 1/2 shoulder with a 1/2 x1/16 groove for grease. This set up seems to have a lot of sideways slop in the shifter, I may need to drill out and add a bushing to the lever. I hope this helps some. Attached Images __________________ 67 K10, lwb, fleetside, 327, 4spd, 205, cab and 3/4 frame swap, 14 bolt, big window, and a "rustoleum roll job" Last edited by eric67m; 11-11-2008 at 02:03 AM.

11-11-2008, 09:25 AM	#3
Ace in the hole Registered User Join Date: Apr 2007 Location: Kalamazoo, Michigan, USA Posts: 538	Re: np205 I got one from manes- it's under "motor, cab & misc. mounts" http://www.manestruckparts.com/store...Category_ID=16 Also found this old thread- http://67-72chevytrucks.com/vboard/s...t=shifter+bolt __________________ 1970 K20, 350--- SOLD 05 silverado extended cab short box- duramax Jeep wrangler unlimited Last edited by Ace in the hole; 11-11-2008 at 09:29 AM.

11-11-2008, 10:36 AM	#4
orangeblossomspecial Registered User Join Date: Sep 2008 Location: Rexburg, Idaho Posts: 34	Re: np205 Many Thanks again, Appreciate the pictures and found what I needed at Manes

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.