![]() |
|
![]() |
#1 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
New Cab Floor
This is why its being replaced, along with previous owner repair work that just wasn't up to snuff.
Last pic is floor cut out from cab.
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Stripping some of the cab to see what kind of nasties are hiding under the paint. And the cab with bracing to keep the original shape/dimensions intact.
We will be replacing the floor with a new one that Tri-Plus makes. It includes the complete underside bracing and supports. We picked it up from TriPro Automotive in NJ. Thanks for the tour John!
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#3 |
can I tuck tractor wheels?
Join Date: May 2009
Location: Colorado Springs , Colorado
Posts: 135
|
Re: New Cab Floor
Good decision to replace the floor. Im planning on doing the same ( I think ) even though mine isn't near this far gone.
__________________
My build page.... http://67-72chevytrucks.com/vboard/s...d.php?t=347666 |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
This is what the rear of the cab looked like after drilling out the spot welds and striping the paint. The PO also welded the floor repairs he did solid to the inside of this. So I replaced it with a piece I made up.
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Second pic shows new piece tack welded and cleco'ed to the back edge of new floor. I left it long for now, so I can cut it just where needed when fitting the cab corners.
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Now onto the firewall seam area, as you can see, it needed attention also. I cut out the rotted area and replaced it with a new piece made up on the brake.
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
I had to repair both sides.
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#8 |
go cyclones
Join Date: Jun 2003
Location: Ames, IA
Posts: 1,885
|
Re: New Cab Floor
Thats some crazy bracing, looking good
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Feb 2007
Location: Cali Central Coast
Posts: 5,191
|
Re: New Cab Floor
Wow - you guys go to extremes to save cabs. I know of a couple of trucks with cabs in better shape than that sitting out in a field.
__________________
'67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD ![]() Click here to support the board Philippians 4: 6-7 |
![]() |
![]() |
![]() |
#10 | |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Quote:
![]()
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
|
![]() |
![]() |
![]() |
#11 | |
Registered User
![]() Join Date: Nov 2003
Location: CT
Posts: 290
|
Re: New Cab Floor
Quote:
How about shipping some of those cabs from Cali to CT? |
|
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Feb 2007
Location: Cali Central Coast
Posts: 5,191
|
Re: New Cab Floor
BTW, I forgot to mention, that's really nice work you're doing on that truck. It's fun to see something like that come back to life. Keep us posted!
__________________
'67 SWB Fleetside ZZ4/350/Tremec 5-speed/4link/Scott's IFS - and fun as heck! SOLD ![]() Click here to support the board Philippians 4: 6-7 |
![]() |
![]() |
![]() |
#13 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,515
|
Re: New Cab Floor
Chas, nice work, good to see some progress. Those floors save alot of work. Can I offer some advice?
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Sure.
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#15 |
Senior Member
![]() Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,515
|
Re: New Cab Floor
Up in post #10, 4th and 5th pic. The 'B' post patch fits great where you have it, but, when you put the rocker on you will have a gap at the lower 'B' post. So you won't have anyway to weld the two together at that point. Also, on the inside the 'B' post patch isn't touching the floorboard, so, if you make an extension on the 'B' post patch panel above those areas, it should drop everything down into alignment and contact. The extension should be all strait bends, nothing complicated. Hope this helps, check out that area when you hang your rocker.
I could be wrong, and I hope I am, but past practice says not. Maybe they fixed this problem since I last worked on that area Nice to watch your work, and seeing your son enjoy it too. Good luck with your truck
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
![]() |
![]() |
![]() |
#16 | |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Quote:
Thanks for the heads up! That is one reason the back of the cab is only attached with cleco's and why the b pillar is only tack welded in, all my measurements and fitting want the b pillar where is is currently, but I didn't like the way it fitted to the floor either. I am rebuilding a door to mount, so I can line up the body lines before doing the rocker or cab corner. I am very anxious to see how everything fits. I can already see the cab corner needs to be bent closer to a 90 degree angle than it was formed. And thanks to the PO lapping new full size/uncut cab corners OVER the existing corner and welding it solid.....it is more of a challenge. But its all good! I love working with metal :] I am having a blast! Logan on the other hand is burnt out on sand blasting for a while lol. chas
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
|
![]() |
![]() |
![]() |
#17 |
ENGINE BUILDER
Join Date: Apr 2006
Location: Shortsville n.y.
Posts: 344
|
Re: New Cab Floor
YOU KRAZY MAN!!!! Very nice work. Most "rust free" trucks I have seen from out west still need rockers and cab corners and footwell work. Western trucks have upper damage from roof caulking that has dried out and allowed water to get in.They rust from the top down. East coast trucks rust from the bottom up.They pretty much all need work.
__________________
JIM ZAG |
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Feb 2009
Location: OKC OK
Posts: 489
|
Re: New Cab Floor
HOLY SMOKES, you make me feel bad for not using parts with just a little pitting on them, you guys are true restorers out east, Me and plenty of others out west would have give up on that one!
__________________
"You can put lipstick on a pig, sure it's pretty pig, but it's still just a PIG... ![]() 71 ![]() |
![]() |
![]() |
![]() |
#19 |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Its only fair that I give Ebfabman credit for his fine cab repair video! It has certainly made the job easier. Thanks Earl!!
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
![]() |
![]() |
![]() |
#20 |
Registered User
Join Date: Nov 2001
Location: Concord, NC
Posts: 2,489
|
Re: New Cab Floor
Anytime....
![]() |
![]() |
![]() |
![]() |
#21 |
ENGINE BUILDER
Join Date: Apr 2006
Location: Shortsville n.y.
Posts: 344
|
Re: New Cab Floor
I saw a 67 from COLORADO last night at a car cruise and it was all original and I am telling you it had NO RUST in the rockers or footwells!!! He would not sell it to ME!!!!
__________________
JIM ZAG |
![]() |
![]() |
![]() |
#22 |
Registered User
![]() Join Date: Apr 2007
Location: Foster Rhode Island
Posts: 1,176
|
Re: New Cab Floor
Where are you located in conn? I live in R.I. and don't get to see to many posts from the east coast.I feel your pain been there done that. Just found a free doner cab a few weeks ago on craigs list.Still needs work , rockers,front floor supports and front floor panels but not the whole thing only over the floor supports and cab corners. but its still a lot better than all the other ones I was going to fix.
|
![]() |
![]() |
![]() |
#23 | |
Registered User
Join Date: Mar 2007
Location: Connecticut
Posts: 581
|
Re: New Cab Floor
Quote:
Good on the CL find! I am in Woodbury, its on the western side of the state. I have been camping at Burlingame for years, are you close by?
__________________
"I'll Procrastinate Tomorrow" quote by LEEVON 71 K10 long fleet (sons truck) new 370hp 355, sm465 np205, 3.73's 33's 70 K20 long fleet 98 G3500 work van |
|
![]() |
![]() |
![]() |
#24 |
Registered User
![]() Join Date: Nov 2003
Location: CT
Posts: 290
|
Re: New Cab Floor
Hey Chas350,
Thanks for letting me stop by to see the progress. It looks good. I am anxious to see how you handle that problem cab corner. Hopefully you will get that door skin soon. I am so itching to get started on my truck build. Hopefully FedEx will drop off my spring compressor today so I can get the Honda out of my garage soon. |
![]() |
![]() |
![]() |
#25 |
Registered User
![]() Join Date: Apr 2007
Location: Foster Rhode Island
Posts: 1,176
|
Re: New Cab Floor
Burlingame is south of here if I'm not mistaken.Foster is on the Conn border on the eastern side,Near Killingly and Sterling not far from Plainfield. Rt 6 runs right through the middle of it.
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|