|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
06-11-2009, 04:18 PM
|
#1 |
|
Registered User
Join Date: Jan 2009
Location: orangevale, ca
Posts: 3,626
|
leaf spring/flip kit question #1001
alright guys, i just ordered a western chassis 5" flip kit. i currently have 4 leaf springs in the pack and i have been sanding and painting them. i was just looking around in my garage and found 6 more leafs i guess i had taken out some time ago(3 on each side). now how many do i need to firm up the rear and get a 5-6" drop w/o a c notch? does it matter since the axle is gonna be on the top now?
they are a pain in the rear to sandblast and i only want to do as many as i'm gonna use. any insight is apprieciated!! thanks, Dennis 
__________________
"Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list 
|
|
|
|
06-11-2009, 04:39 PM
|
#2 |
|
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: leaf spring/flip kit question #1001
flip kit and 3 leafs no over load
 flip kit and 5 leafs no over load 
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 |
|
|
|
|
06-11-2009, 05:09 PM
|
#3 |
|
Registered User
Join Date: Jan 2009
Location: orangevale, ca
Posts: 3,626
|
Re: leaf spring/flip kit question #1001
thanks aaron, now how do u tell which are overloads? the ones w/o the pads on the ends?
__________________
"Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list
|
|
|
|
|
06-11-2009, 05:30 PM
|
#4 |
|
6.0 powered square
Join Date: Feb 2008
Location: Mesquite texas
Posts: 3,459
|
Re: leaf spring/flip kit question #1001
the over loads are flat about a inch thick and are on the bottom of the leaf packs
__________________
Aaron 1980 c-10 short bed lowered, cammed 6.0, 4l80e 3600 stall, smp tune, wilwoods, and flames best time so far best et 7.86 @87 on motor 7.57 90 on a 75 shot Build http://67-72chevytrucks.com/vboard/s...d.php?t=283326 |
|
|
|
|
06-11-2009, 06:19 PM
|
#5 |
|
Registered User
Join Date: Jan 2009
Location: orangevale, ca
Posts: 3,626
|
Re: leaf spring/flip kit question #1001
gotcha, i dont have any overloads then...
__________________
"Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
