buying cross over

[dammitmitchell]

anyone knwo where to buy a kit fro crossover?
thanks

[konajoe]

Off Road Design

Dana 60
http://www.offroaddesign.com/catalog...0crossover.htm

Dana 44/10 bolt
http://www.offroaddesign.com/catalog...4crossover.htm

[dammitmitchell]

OMFG that's expensive... yeap my wife instantly vetoed that one...
dang... maby i'll luck out and find a used one...

[Oilbrnr]

Originally Posted by dammitmitchell

OMFG that's expensive... yeap my wife instantly vetoed that one...
dang... maby i'll luck out and find a used one...

That doesn't include the price of the 2WD steering box or flat-tops either...

[konajoe]

Do you plan on wheeling your truck? How much lift does your truck have? If you just plan to dd/cruise then you maybe able to get by with the standard steering corrections.

[OLDCHEV4X4]

I made my own. Being a machinist has its advantages.

2wd power steering box from the warehouse. (out back of the house)
1 ton drag link ends from NAPA
Pc of round bar for the drag link
steering arm from Mad FWD, with studs, cones and nuts
pitman arm from a 78 Ford F150.
flat top knuckle was on the Blazer already.

The boss bought me the LH tap for the drag link.
I had to buy a tappered ream for the steering arm and the pitman arm.
Then i took everything to work and went to town.
I had to heat up the pitman arm and bend it a little so it wouldn't hit the frame.
So far so good. No failures.

[duallyjams]

Originally Posted by oldchev4x4

i made my own. Being a machinist has its advantages.

2wd power steering box from the warehouse. (out back of the house)
1 ton drag link ends from napa
pc of round bar for the drag link
steering arm from mad fwd, with studs, cones and nuts
pitman arm from a 78 ford f150.
Flat top knuckle was on the blazer already.

The boss bought me the lh tap for the drag link.
I had to buy a tappered ream for the steering arm and the pitman arm.
Then i took everything to work and went to town.
I had to heat up the pitman arm and bend it a little so it wouldn't hit the frame.
So far so good. No failures.

show off

[turp mcspray]

Check out the "how to" on colorado k/5. This guy did his own and did a few things to lower the cost. It is a good read.

[johnnywagon]

I really like the kit I got from Blackbirds: http://www.blackbirdscustomtrucks.com/

[drink2mny]

Originally Posted by johnnywagon

I really like the kit I got from Blackbirds: http://www.blackbirdscustomtrucks.com/

Thanks big guy..

Plus I am on here to answer any questions you might have...

[Oilbrnr]

Originally Posted by drink2mny

Thanks big guy..

Plus I am on here to answer any questions you might have...

Coolio. So a 2WD box is all that is needed for the 44 correct? Works with '73+ as well?

[whiskeydented]

Not sure what you have for an axle but I just bought these arms for my d60.

http://www.ballisticfabrication.com/...es_p_1246.html

[dammitmitchell]

8 in lift
on corp 10-bolt front
running 37's....
hmmmmm...
well all this is because my stock steering stabalizers are now kaput...
cannot compress or extend one of them.. adn teh second goes in and otu too easily.. and not with a full range of motion either..
thnaks..

[OLDCHEV4X4]

Originally Posted by dammitmitchell

8 in lift
on corp 10-bolt front
..

You will have a problem with the center link. D44 flat top knuckle TRE's come down from the top. 10 bolts come up from the bottom. Are you going to use matching knuckle's?
You cant mix and match.

[drink2mny]

Yup, a truck 2wd box

[dammitmitchell]

ok..
well iw as roaming the junkyard this week and i had yet ANOTHER cross over question
i have my D44 knuckel
NOW.. i noticed on some of the camper specials and k20 series trucks that they have the 2wd set up that looks like cross over..

(look at the 2wd parts uptop)
http://www.lmctruck.com/icatalog/cc/full.aspx?Page=139

can i use any of this to build my own?
i am determined to make my own without it looking god awful and dangerous

[OLDCHEV4X4]

The only thing you need there is the 2WD steering box.

[dammitmitchell]

damn..
well it was tempting..
so.. 2wd steering box..
and knuckle coming in...
what do i have to tell the machine shop to mill? or should i just wait until the highsteer arms come in and then have them "match" it ..?

[OLDCHEV4X4]

Originally Posted by dammitmitchell

what do i have to tell the machine shop to mill? or should i just wait until the highsteer arms come in and then have them "match" it ..?

They have to mill the top of the knuckle flat. Google D44 flat top crossover steering, or something close to that, and it will come up. It will save the machinist alot of time if he dosent have to reverse engineer the steering arm pattern.
If the arm comes with out a tapered hole for the TRE, then give him the TRE too so he can try it.

[dammitmitchell]

both will have the aftermarket high steer arms,
so then the tie rod ends should be matched then.....
right? how would the stock locations effect aftermarket parts?
i can go get another d44 knuckle
but i havent been seeing both come in a kit for the crossover kits labeled for "d44 and corp 10" come with all the same equipment...

[OLDCHEV4X4]

If you were just doing crossover, it would matter because the center link ends go in from the top on a D44, and up from the bottom on a 10 bolt.
But...since your doing high steer (you said crossover not high steer) you could probley get away get away with the 10 bolt knuckle on the driver side.
You should keep your knuckles in pairs. But...do what you have to do.

[dammitmitchell]

sweet..
i was freaked out and was hoping it was a misunderstanding,
with most "highsteer/crossover? kits it pretty much seems to only be the pitman arms that are changed.. (or whatever the name is for the arm on knuckle itself)

[OLDCHEV4X4]

steering arm