![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Used to have a truck
Join Date: May 2002
Location: port orchard WA
Posts: 1,552
|
How do I know if my carrier bearing is going out?
Does it go "ee er ee er ee er" under 20 mph or so ? I can push up and down on the first driveshaft 3/16" or so . Its kind of a rubbery sound. Checked all my wheel bearings . Cant figure out where the sound is coming from . seem s like its undeer the truck though. Help !!!!
__________________
No truck :-( |
![]() |
![]() |
![]() |
#2 |
My other Love
Join Date: Aug 2001
Location: Castlegar B.C. Canada
Posts: 4,085
|
Yes thats your carrier bearing , exact same sound was on my 74 cheyenne super 20 before I replaced it
__________________
![]() Castlegar B.C.The great white North (Canada Eh!) Hooter_5@hotmail.com First generation Monte Carlo club pictures of my life |
![]() |
![]() |
![]() |
#3 |
Used to have a truck
Join Date: May 2002
Location: port orchard WA
Posts: 1,552
|
How does it come out. I just called the parts store and they want me to bring it in . Seems theres quite a few . My luck it'll be an oddball one .
__________________
No truck :-( |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Feb 2002
Location: Vacaville, CA
Posts: 2,746
|
The carrier bearing is pressed onto the driveshaft. I have never chenged one before, but I am about to find out how to do it too. lol I think there are 3 or 4 types, so you might be able to tel which one you have without bringing it in. The ones the parts stores seel aren't excatly the best quality, so I got one from here: http://www.iedls.com/ They have 2 different kinds, and they are way better than anything else i have seen.
__________________
![]() ![]() 99 Pontiac S/C GTP, SLP Ram Air hood, GMPP Konis & springs 95 Neon ACR, MP PCM, AFX UDP, 3.0 CAI |
![]() |
![]() |
![]() |
#5 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
I used a propain tortch and a hammer to get mine off. Only took 15 min or so.
I was told there was no way it'd come off that way...but it did. Then on reassembly...it was winter so the shaft was already cold...I tossed the C-bearing into the stove for a few min, put some light oil on the shaft, and it slid all most all the way on by hand. Just some love taps with a small tap tap hammer. Last edited by Longhorn Man; 01-16-2003 at 12:42 AM. |
![]() |
![]() |
![]() |
#6 |
Low & Slow
Join Date: Dec 2002
Location: Oklahoma
Posts: 1,047
|
Here's what I did.pull the driveshaft out of the truck. You have to get the middle u-joint out of the driveshaft. There will be a bolt going through the yoke on the same side that the carrier bearing is on. Take that bolt out pull the yoke off and beat the hell out of the carrier bearing with a mallet. When you go to put it back on push it onto the driveshaft as much as you can then use the yoke and the bolt that holds the yoke to press it in the rest of the way. You might want to change your other two u-joints at the same time. Hope that helps. good luck
__________________
70' C-10 LWB Fleetside 4.5/6 drop ![]() |
![]() |
![]() |
![]() |
#7 |
Low & Slow
Join Date: Dec 2002
Location: Oklahoma
Posts: 1,047
|
Hey longhorn...I never thought about using a torch. lol that would have probably saved me about 30 minutes worth of beating the crap out of it. Oh well... I got some of my anger out.
__________________
70' C-10 LWB Fleetside 4.5/6 drop ![]() |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Dec 2002
Location: Citrus Heights Ca.
Posts: 186
|
I actually put a carrier bearing on my "71 C-10 yesterday. It had the light duty bearing with the two inline (with the driveshaft)bolts. I had never done one before. Cost 32.95 from napa. I did a search on this board for some hints. Can't remember who, but someone posted a real indepth how too on the subject. I just used sledge hammers, vice, big sockets, and a short piece of pipe (to drive the new one on. Luckily no torches. It's easyier than it looks. Except for dropping the sledge on my big toe!
__________________
Ethan '71 C-10 LWB Cheyenne 85K miles. "Time spent Boating is NOT deducted from ones lifespan". |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Dec 2002
Location: Citrus Heights Ca.
Posts: 186
|
Here was mine before I did it with my 5 year old goofing with it.
__________________
Ethan '71 C-10 LWB Cheyenne 85K miles. "Time spent Boating is NOT deducted from ones lifespan". |
![]() |
![]() |
![]() |
#10 |
Pronounced "Pew-al-up"
Join Date: Oct 2002
Location: Puyallup, Washington
Posts: 845
|
Hey MikeP, I did mine a couple of months back because
it was making the same noise as yours. I just took it to national auto parts in Tacoma, and they pressed it off and put the new one on for about $15. Money well spent unless you like to beat on things... Hadem' slap on some new u-joints while they were at it.!! ![]()
__________________
Classic GM Trucks of Washington Club Member 1970 FS chevy,350/350, Edelbrock cam and intake. Holley 650 carb,HEI,AT,Tangier Orange, 18's, Power Locks, Truck Photos |
![]() |
![]() |
![]() |
#11 |
Used to have a truck
Join Date: May 2002
Location: port orchard WA
Posts: 1,552
|
Mine looks nothing at all like that. It's the one with the bolts on the side. I assume most 3/4 tons will have the same one I do. Since the vast majority of the 67-72's in this area are 3/4 tons I hope the parts store has the one I'll need. I'd hate to pull the damned thing out on Sunday and find they have to order it in. I kind of like to drive it to work and stuff.
I hate to do it at all to be honest. I'll be installing the short step bed this summer with a corresponding short or shortened frame and a one piece driveshaft. It looks like thang is just pressed on the middle yoke. Is that it? If so then its no big deal. I have a 30 ton enerpac electric over hydraulic shop press.
__________________
No truck :-( Last edited by mikep; 01-16-2003 at 01:09 AM. |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Dec 2002
Location: Citrus Heights Ca.
Posts: 186
|
$15????? Hummmmmm, mean I realy wouldn't have had to drop that sledge on my foot? It would have been worth it to pay the $15 if I didn't have to wait too long or drive too far.
__________________
Ethan '71 C-10 LWB Cheyenne 85K miles. "Time spent Boating is NOT deducted from ones lifespan". |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Jul 2001
Location: utica, oh,
Posts: 249
|
I had the same one you are talking about on my 2wd and I had to cut mine off with a torch. I pride my self on my large selection of "bfh's" and none of them worked for me so I had to shave it off with my favorite wrench, the hot wrench. The i just used a piece of pipe and a hammer to tap the new one on.
__________________
69 3/4 ton 4x4 gmc with 6" sky jacker soft ride. 350 / th350 / 205 work in progress Last edited by 694X4; 01-16-2003 at 10:19 AM. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|