CAb Mounting question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Tynee · 01-18-2003, 10:33 AM

Vendors sell cab mounting kits with rubber and hardware or just rubber, could all the hardware be bought at my local Ace Hardware for lss than the $20 difference in price?

Thanks,
Tynee

JimKshortstep4x4 · 01-18-2003, 10:48 AM

I am not sure what the hardware includes, but I assume that it is the washers, nuts, and spacers. If the hardware includes the front and rear bolts, then I would buy the kit. You can make the spacers out of the right size pipe. Getting the large washers may be a problem. Finding the 9/16" nuts for the front will take some effort. If you need the rear bolts, those are hard to find, but you can make them with a 7/16" nut welded to threaded rod. The 9/16" front bolts are hard to find.

If your parts are good, that can make a difference, also.

Jim

jim71chevy · 01-18-2003, 10:53 AM

I would to know that to, I was going to buy some soon and was wondering that??

JimKshortstep4x4 · 01-18-2003, 11:09 AM

I am looking at Chevy Duties listing of hardware and it includes the steel bushings, washers, bolts, nuts, and shims. It would be hard to get what you need from a local hardware and the parts will probably be more than $20. The last time that I got 9/16"
bolts from the specialty fastener company, they were $6 each or $12 for both. If the kit that you are looking at includes the bolts than $20 extra is well worth it.

Check your bolts to make sure that you need them before deciding.

Jim

**Yukon Jack** · 01-18-2003, 11:25 AM

Definitely buy the kit!

Southpa · 01-18-2003, 07:36 PM

I bought the complete cab mounting kit a few years back, it included everything for all 6 mounts, rubber, bolts, nuts, washers, spacers, unfortunately no instructions, lol. You better remember where everything goes when you remove the old ones. Btw, the kit cost me $102 Cdn. ya, I know, but they were the only game in town.

Dads72 · 01-18-2003, 10:15 PM

If memory serves me correctly, the back bolts are pointed, and go into nuts already welded onto the cab floor. They come up from the bottom.
The front bolts go down from the top.
Correct?
I bought one of the kits for my 72. Had to add several washers in the rear to make the side trim line up.

01-18-2003, 10:33 AM	#1
Tynee I miss this truck. Join Date: Dec 2001 Location: Lexington, KY U.S.A. Posts: 2,863	CAb Mounting question Vendors sell cab mounting kits with rubber and hardware or just rubber, could all the hardware be bought at my local Ace Hardware for lss than the $20 difference in price? Thanks, Tynee __________________ '07 GMC Acadia SLT. Sweet ride. '08 Crew Cab Z-71 short bed. Really like this truck A LOT.

01-18-2003, 11:25 AM	#5
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Definitely buy the kit! __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

01-18-2003, 07:36 PM	#6
Southpa Registered User Join Date: May 2000 Location: Victoria, BC, Canada Posts: 2,410	I bought the complete cab mounting kit a few years back, it included everything for all 6 mounts, rubber, bolts, nuts, washers, spacers, unfortunately no instructions, lol. You better remember where everything goes when you remove the old ones. Btw, the kit cost me $102 Cdn. ya, I know, but they were the only game in town. __________________ 1970 GMC 1500 Custom Original 350/TH350 Victoria, BC, Canada You can wish in one hand and crap in the other. See which one gets filled first.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

01-18-2003, 10:48 AM	#2
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	I am not sure what the hardware includes, but I assume that it is the washers, nuts, and spacers. If the hardware includes the front and rear bolts, then I would buy the kit. You can make the spacers out of the right size pipe. Getting the large washers may be a problem. Finding the 9/16" nuts for the front will take some effort. If you need the rear bolts, those are hard to find, but you can make them with a 7/16" nut welded to threaded rod. The 9/16" front bolts are hard to find. If your parts are good, that can make a difference, also. Jim

01-18-2003, 10:53 AM	#3
jim71chevy Registered User Join Date: Apr 2001 Location: Canton, Ill Posts: 48	I would to know that to, I was going to buy some soon and was wondering that??

01-18-2003, 11:09 AM	#4
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	I am looking at Chevy Duties listing of hardware and it includes the steel bushings, washers, bolts, nuts, and shims. It would be hard to get what you need from a local hardware and the parts will probably be more than $20. The last time that I got 9/16" bolts from the specialty fastener company, they were $6 each or $12 for both. If the kit that you are looking at includes the bolts than $20 extra is well worth it. Check your bolts to make sure that you need them before deciding. Jim

01-18-2003, 10:15 PM	#7
Dads72 Registered User Join Date: Nov 2002 Posts: 427	If memory serves me correctly, the back bolts are pointed, and go into nuts already welded onto the cab floor. They come up from the bottom. The front bolts go down from the top. Correct? I bought one of the kits for my 72. Had to add several washers in the rear to make the side trim line up.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.