![]() |
|
![]() |
#1 |
Registered User
Join Date: Oct 2009
Location: Sacramento, CA
Posts: 161
|
Ticking Wheel
My front passenger side wheel is ticking. I figure it's a bearing problem, but I don't really have time to do the brakes/bearings this weekend, and I need the truck to haul some lumber for a fence. Am I going to cause any catastrophic damage if I drive the truck about 100 miles this weekend? I don't know much about bearings and whatnot.
__________________
1972 Chevy C-10 ~ 188,000 miles give or take |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: Ticking Wheel
If it is a bearing then you could have some real problems very shortly.
Do you have trim rings on your wheels? They can cause a tick. Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
![]() |
![]() |
![]() |
#3 |
Special Order
![]() ![]() Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,859
|
Re: Ticking Wheel
If you just noticed it started making the noise it should good for a few more careful miles.But,you didn`t hear that from me.I ain`t recommending squat.
![]() Take the time to jack the wheel up to check for wear or slop.Also,listen to and watch it spin.Then decide.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: May 2006
Location: Jonesboro, AR
Posts: 916
|
Re: Ticking Wheel
Most of the time I have had a ticking noise it was as foreign object. Does it tick only on pavement or all the time? Either a rock or nail/bolt in the tread will cause this too.
|
![]() |
![]() |
![]() |
#5 |
Big Red - Now its a SWB!
Join Date: Jun 2009
Location: Oroville, Ca
Posts: 1,624
|
Re: Ticking Wheel
that's what I was thinking too! I have an explorer with aggressive tires and live on a gravel road so this happens all the time to me....once you get up to about 60 it's usually out!
__________________
68 3/4 ton ![]() ![]() 41 3/4 ton ![]() 01 Tahoe LT 4WD (my daily driver)-Magnaflow Muffler, Rollin on 22's 02 Ford Mustang Convertable (Wife's Car)-Flowmaster 50, Clear corners, Intake, sittin on 18's Last edited by Jacfourteen; 12-12-2009 at 08:54 PM. |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Oct 2009
Location: Sacramento, CA
Posts: 161
|
Re: Ticking Wheel
Yeah, I was thinking there may be something in there, but I checked the tire, and it only ticks when it's on the ground. When it's up in the air, it is quiet. It's okay, though, brakes/rotors/bearings are getting done tomorrow after all. . .
__________________
1972 Chevy C-10 ~ 188,000 miles give or take |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Aug 2009
Location: St. Paul MN.
Posts: 1,996
|
Re: Ticking Wheel
I have seen loose brake pads do this also cotter pins hitting on a beat up bearing dust cap.
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Oct 2009
Location: Sacramento, CA
Posts: 161
|
Re: Ticking Wheel
Well, we'll see. Tomorrow's brake/bearing day. Anything that I should know in order to make this go smoothly??? Specifically any tips for packing the bearings with grease? Just grease 'em up and pack 'em in?
__________________
1972 Chevy C-10 ~ 188,000 miles give or take Last edited by Mike Quillici; 12-13-2009 at 03:47 AM. Reason: More info. |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Apr 2002
Location: New Carlisle, Ohio,USA
Posts: 1,404
|
![]()
Don't just wipe grease on the bearings and put them in. You have to work the grease into the bearings. Put some grease in the palm of one hand, take the bearing in the other hand, and with the large side towards the grease, just tap the bearing into the grease in your hand. After a bit, you'll notice the grease start appearing at the
top, small, side of the bearing. After you've done that all the way around the bearing, THEN you wipe some on the outside of the bearing, (now your bearing is packed), and put it in. Hope this helps?
__________________
![]() ![]() ![]() LIFE AIN'T EASY WHEN YER FAT AND GREASY! GMC= Got More Class! ![]() ![]() |
![]() |
![]() |
![]() |
#10 |
Account Suspended
Join Date: Apr 2009
Location: Oklahoma City
Posts: 4,709
|
Re: Ticking Wheel
The last time I had a ticking noise from a wheel it was coming from the loose center cap. Before that it was the busted joint on my right front axle in the 4x4 but that was a little more than a tick.
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Oct 2009
Location: Sacramento, CA
Posts: 161
|
Re: Ticking Wheel
Alright. New bearings, rotors, and brake pads. The pads were so warn, that they were metal on metal in some places. Took her for a spin, and she stops. So, I couldn't ask for much more. Thanks everyone.
__________________
1972 Chevy C-10 ~ 188,000 miles give or take |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|